Shark WANDVAC WS640AE Vacuum Cleaner Manual

The Shark WANDVAC WS640AE is a lightweight, cordless stick vacuum cleaner designed for quick cleanups and versatile floor-to-ceiling cleaning. It features a powerful motor, a removable handheld pod, a crevice tool, a multi-surface brush roll, a wall-mountable charging dock, and a washable filter. Powered by a rechargeable lithium-ion battery, it offers multiple suction modes and is ideal for hard floors and carpets. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Cleaning Modes & Techniques 8. Maintenance & Care 9. Safety Information 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main vacuum body (pod), Extension wand, Multi-surface floor nozzle, Crevice tool, Wall-mounted charging dock, Washable filter, Lithium-ion battery.

Feature	Description
Power Button	Turns vacuum on/off; cycles through suction modes
Battery Indicator LED	Shows battery charge status (Green/Red)
Release Buttons	For detaching handheld pod and attachments
Charging Contacts	On dock and vacuum for recharging
Dust Cup Empty Lever	Releases dirt into trash
Washable Filter	Captures fine dust; removable for cleaning
Multi-Surface Brush Roll	Adjusts for hard floors and carpets
Crevice Tool	For tight spaces, corners, and upholstery
Wall Dock	Mounts on wall for storage and charging
LED Headlights	On floor nozzle to illuminate debris

Assembly & Installation

Unpack all parts and inspect for damage. Assemble before first use.

Attach the wand: Insert the wand into the main vacuum body until it clicks.
Attach the floor nozzle: Connect the nozzle to the end of the wand until secure.
Mount the charging dock: Use included screws to mount on wall near outlet; ensure dock is level.
Place vacuum on dock: Align charging contacts; vacuum will charge automatically.

WARNING! Ensure vacuum is turned off during assembly. Keep hands clear of moving parts.

First-Time Setup

Charge fully before first use. Install attachments as needed.

Initial charge: Place vacuum on dock; charge until battery LED turns solid green (approx. 3.5 hours).
Test power: Press power button to turn on; cycle through suction modes (Low, High).
Empty dust cup: Press empty lever to release any packaging debris.
Check filter: Ensure filter is properly seated inside dust cup.

CAUTION! Do not use vacuum while charging. Use only Shark-approved accessories.

Specifications

Model: WANDVAC WS640AE.
Type: Cordless stick vacuum with handheld option.
Battery: Rechargeable lithium-ion, 22.2V.
Run Time: Up to 30 minutes on Low, 15 minutes on High (varies with use).
Charge Time: Approximately 3.5 hours.
Dust Cup Capacity: 0.15 dry quarts.
Weight: 3.5 lbs (with wand and nozzle).
Suction Modes: Low (Eco), High (Max).
Attachments: Multi-surface floor nozzle, crevice tool.
Filter: Washable foam and felt filter.
Warranty: 1-year limited warranty.

Controls and Settings

Power Button: Press once for Low (Eco) mode, press again for High (Max) mode, press again to turn off. Battery LED: Solid green = fully charged; Flashing green = charging; Solid red = low battery; Flashing red = fault/overheating.

Using Handheld Mode: Press release buttons to detach pod from wand; attach crevice tool directly for above-floor cleaning.

Emptying Dust Cup: Hold over trash; press empty lever to open bottom gate; tap to remove debris.

Using Attachments

Multi-Surface Floor Nozzle: For carpets and hard floors; LED lights activate when vacuum is on. Crevice Tool: For tight spaces, between cushions, along edges.

Turn off vacuum before changing attachments.
To attach: Align and push until click is heard.
To detach: Press release buttons and pull apart.

Tip: Clear brush roll of hair and fibers regularly to maintain performance.

Cleaning Modes & Techniques

For best results, select mode based on surface.

Low (Eco) Mode: For longer run time on hard floors and light debris.
High (Max) Mode: For deep cleaning carpets and concentrated messes.
Handheld Mode: Detach pod for stairs, furniture, and cars.
Empty dust cup when debris reaches MAX line for optimal suction.
Use slow, overlapping passes for thorough cleaning.

WARNING! Do not vacuum wet spills, large objects, or hot ashes. Avoid vacuuming cords.

Maintenance & Care

Regular maintenance ensures peak performance.

Empty dust cup after each use.
Clean filter monthly: Remove, rinse under cold water, air dry 24 hours completely before reinstalling.
Clear brush roll: Use scissors to cut away wrapped hair and fibers.
Check for blockages: Inspect wand, nozzle, and openings if suction decreases.
Store on charging dock to keep battery charged.

CAUTION! Do not use vacuum without filter installed. Ensure all parts are completely dry before use.

Safety Information

Read all instructions before use. Keep hair, loose clothing, fingers away from openings. Unplug charger when not in use. Use only with Shark-branded batteries and chargers. Do not use if damaged. Keep away from children. Not for outdoor use.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © SharkNinja Operating LLC. Shark, WANDVAC, and associated designs are trademarks of SharkNinja. For support, visit sharkclean.com or call 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Battery dead/not charged	Place on dock; charge fully. Ensure contacts are clean.
Weak suction	Full dust cup, clog, dirty filter	Empty dust cup; check for blockages; clean/replace filter.
Brush roll not spinning	Hair/debris wrapped around roll	Turn off; clear obstruction from brush roll.
Battery not charging	Dirty contacts, faulty outlet/dock	Clean contacts on vacuum and dock; try different outlet.
Vacuum turns off during use	Overheating, battery protection	Allow to cool for 45 minutes; check for blockages.
LED lights not working	Nozzle not connected properly	Turn off; reconnect nozzle securely.

Reset: Remove from dock; hold power button for 10 seconds; re-dock.

Service: 1-800-798-7398; sharkclean.com