Shark VACMOP RV2000WD Series Vacuum Cleaner Manual

The Shark VACMOP RV2000WD Series is a versatile 2-in-1 cordless vacuum and mop system designed for hard floors. It features a self-cleaning brushroll, dual tank technology (clean and dirty water separation), multi-surface cleaning capabilities, LED headlights, a lightweight design, and a rechargeable battery. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Functions 6. Cleaning Modes 7. Maintenance & Cleaning 8. Battery & Charging 9. Storage & Care 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Vacuum & mop pod, Handle, Clean water tank, Dirty water tank, Self-cleaning brushroll, Charging dock, LED headlights, Multi-surface cleaning pad.

Feature	Description
Self-cleaning brushroll	Automatically cleans hair and debris during use
Dual tank technology	Separates clean water and dirty water for hygienic cleaning
LED headlights	Illuminates hidden dirt and debris
Cordless design	Rechargeable battery for convenient mobility
Multi-surface cleaning	Works on hard floors, tile, laminate, and vinyl
Lightweight handle	Easy to maneuver and store
Charging dock	For convenient storage and charging
Washable cleaning pad	Reusable pad for eco-friendly cleaning
POWER button	Turns vacuum and mop functions on/off
Battery indicator	Shows remaining battery life

Assembly & Setup

Unpack and inspect all contents. Assemble before first use.

Attach handle: Insert handle into vacuum pod until it clicks securely.
Install clean water tank: Fill with recommended cleaning solution and snap into place.
Attach dirty water tank: Ensure it is securely locked on the back.
Attach cleaning pad: Align pad with pod and press until secured.
Place on charging dock: Connect charger to dock and plug into outlet.

WARNING! Do not use with wet hands. Ensure all parts are completely dry before assembly.

First-Time Use

Fully charge the battery before first use.

Charge: Place vacuum on dock; charge until indicator shows full (approx. 4 hours).
Fill clean water tank: Use Shark cleaning solution or approved alternative.
Power on: Press POWER button to start vacuum and mop functions.
Begin cleaning: Glide over hard floors; unit will vacuum and mop simultaneously.
Self-clean: Press CLEAN button to clean brushroll after use.

CAUTION! Only use on hard floors. Do not use on carpets or rugs.

Specifications

Model: Shark VACMOP RV2000WD Series.
Type: Cordless 2-in-1 vacuum and mop.
Battery: Rechargeable lithium-ion.
Run Time: Up to 30 minutes per charge.
Charging Time: Approximately 4 hours.
Tank Capacity: Clean water: 450ml; Dirty water: 450ml.
Weight: 3.5 kg (without tanks).
Cleaning Path: 25 cm.
Power Source: 100-240V AC, 50/60Hz.

Controls and Functions

Main controls located on handle. Handle: POWER button, Battery indicator, CLEAN button.

Indicator Lights: Green (full charge), Yellow (medium), Red (low), Flashing red (needs charge).

Vacuum & Mop: Simultaneous suction and mopping. Self-cleaning: Press CLEAN button to clean brushroll; unit will run for 30 seconds. Battery: Indicator shows remaining charge; automatic shutoff when battery is low.

Cleaning Modes

Standard mode: For everyday cleaning. Spot mode: For concentrated cleaning (press and hold POWER).

Ensure clean water tank is filled and dirty water tank is empty.
Press POWER to start; glide forward and backward over floor.
For stubborn stains, use spot mode by pressing and holding POWER.
After cleaning, press CLEAN button to self-clean brushroll.

Tip: Move slowly for deeper cleaning; faster for light cleaning.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Empty dirty water tank after each use.
Rinse clean water tank and refill with fresh solution.
Remove and wash cleaning pad; air dry completely.
Clean brushroll: Remove debris; rinse if necessary.
Wipe exterior with damp cloth; do not submerge.

WARNING! Unplug charger before cleaning. Do not immerse in water.

Battery & Charging

Use only provided charger. Charge fully before first use.

Charging: Place on dock; indicator flashes while charging, solid when full. Battery Care: Avoid extreme temperatures; store in cool, dry place. Replacement: Battery not user-replaceable; contact Shark for service.

Storage & Care

Store upright on charging dock. Empty tanks and remove pad before storage.

CAUTION! Do not store with water in tanks. Keep away from heat sources.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Charge fully for 4 hours; ensure dock is powered.
Poor suction/no mopping	Clogged brushroll/empty tank	Clean brushroll; ensure clean water tank is filled.
Leaking water	Tanks not sealed properly	Check tank seals; reinstall tanks securely.
Brushroll not spinning	Debris wrapped around roll	Turn off; remove debris; press CLEAN button.
Battery not charging	Faulty connection	Check dock connection; try different outlet.

Reset: Remove battery for 10 minutes; reinstall and charge.

Service: 1-800-798-7398; sharkclean.com