Shark V1730CR Vacuum Cleaner Manual

The Shark V1730CR is a versatile upright vacuum cleaner featuring powerful suction, a HEPA filtration system, multiple cleaning modes (carpet, hard floor, above-floor), a motorized brushroll, a large-capacity dust cup, washable filters, LED headlights, and a lightweight, swivel-steer design for easy maneuverability. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main vacuum body with motor, Handle with controls, Motorized brushroll, Dust cup with release latch, HEPA filter, Washable pre-motor filter, LED headlights, Swivel steering, Hose and wand for above-floor cleaning.

Assembly & Setup

Unpack all parts from the box. Ensure all components are present.

1. Attach the handle: Align the handle with the main body until it clicks into place.
2. Install the wand and hose: Connect the wand to the hose port on the front of the vacuum.
3. Attach cleaning tools: Clip the desired tool (crevice tool, dusting brush, upholstery tool) to the wand or storage caddy.
4. Check filters: Ensure both the pre-motor filter and HEPA filter are properly seated.

WARNING! Do not operate the vacuum before it is fully assembled. Keep fingers away from the brushroll during assembly.

First-Time Use

Before first use, fully charge the vacuum (if cordless) or plug into a suitable outlet.

1. Select cleaning mode: Use the dial/switch to select CARPET, HARD FLOOR, or OFF (for above-floor).
2. Power on: Press the power button on the handle.
3. Adjust suction: Use the variable suction control if available.
4. Begin cleaning: Push the vacuum forward and back in slow, overlapping strokes.
5. For above-floor cleaning: Detach the wand and attach the desired tool.

CAUTION! Ensure the brushroll is off when cleaning delicate area rugs or hard floors to prevent damage.

Specifications

• Model: Shark V1730CR.
• Type: Upright vacuum cleaner.
• Power Source: 120V AC, 60Hz (Corded) / Rechargeable Lithium-Ion Battery (Cordless variant).
• Filtration: HEPA + Washable Foam Filter.
• Dust Cup Capacity: 1.2 Dry Quarts.
• Cord Length: 25 feet (for corded models).
• Weight: Approximately 12.5 lbs.
• Attachments Included: Crevice Tool, Dusting Brush, Upholstery Tool, Pet Multi-Tool.
• Warranty: Limited 5-year warranty (refer to warranty card).

Controls and Settings

Main controls are located on the handle and body.

Handle: Power On/Off button, Suction Control slider (if applicable). Body: Brushroll On/Off switch, Cleaning Mode selector (Carpet/Hard Floor/Off), Dust Cup Release button, Wand Release button.

Cleaning Modes: CARPET (brushroll on, full suction), HARD FLOOR (brushroll off or reduced suction), OFF (for using hose and wand). Suction Control: Adjust power for different surfaces or to prevent rug fringes from being sucked in. Brushroll Control: Turn off for delicate rugs or to reduce noise on hard floors.

Cleaning Modes & Attachments

Use the correct mode and attachment for optimal cleaning results.

1. For carpets: Use CARPET mode with brushroll on.
2. For hard floors (wood, tile): Use HARD FLOOR mode with brushroll off.
3. For stairs and above-floor: Detach the wand and hose. Attach the appropriate tool:
   • Crevice Tool: For tight spaces, corners, and along baseboards.
   • Dusting Brush: For lampshades, blinds, and delicate surfaces.
   • Upholstery Tool: For sofas, chairs, and car interiors.
   • Pet Multi-Tool: Combines bristles and a crevice tool for pet hair.

Tip: Clear the area of large debris and cords before vacuuming to prevent clogs.

Emptying & Cleaning the Dust Cup

Empty the dust cup when it reaches the MAX fill line.

1. Turn off and unplug the vacuum.
2. Press the Dust Cup Release button and lift the cup away from the body.
3. Hold the cup over a trash can. Press the bottom release latch to open the door, allowing debris to fall out.
4. Tap the cup gently to dislodge fine dust. If necessary, use a dry cloth to wipe the interior.
5. Close the latch securely and reattach the dust cup to the vacuum until it clicks.

WARNING! Always turn off and disconnect power before emptying the dust cup. Do not use water to clean the dust cup interior.

Filter Maintenance

Clean filters regularly to maintain suction and performance.

Pre-Motor Foam Filter: Rinse under cool water until water runs clear. Squeeze out excess water and let air dry completely for 24 hours before reinstalling. HEPA Filter: Tap gently over a trash can to remove loose dust. Do not wash. Replace the HEPA filter every 6-12 months under normal use, or as needed.

Care & Storage

Unplug and turn off before any care or maintenance. Store in a cool, dry place.

Brushroll Maintenance: Regularly check for and remove hair, threads, or debris wrapped around the brushroll. Use scissors to carefully cut and remove obstructions. General Care: Wipe the exterior with a dry or slightly damp cloth. Never immerse the vacuum in water or use harsh chemicals.

CAUTION! Ensure all filters are completely dry before reinstalling. A wet filter can damage the motor.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B. Operation is subject to the condition that this device does not cause harmful interference. Copyright © SharkNinja Operating LLC. Shark and V1730CR are trademarks of SharkNinja. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: For cordless models, try a full power cycle by turning off and removing the battery for 60 seconds.

Service: 1-800-798-7398; www.sharkclean.com