Shark UVC805C Vacuum Cleaner Manual

The Shark UVC805C is an upright vacuum cleaner with powerful suction, a HEPA filtration system, multiple cleaning modes, and specialized attachments for versatile floor-to-ceiling cleaning. It features a lightweight design, easy-empty dust cup, motorized brush roll for carpets, and swivel steering for maneuverability. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Cleaning Modes 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Upright vacuum body, motorized floor nozzle, dust cup with HEPA filter, hose with wand, crevice tool, dusting brush, upholstery tool, and power cord.

Feature	Description
Powerful Suction	High-performance motor for deep cleaning on carpets and hard floors
HEPA Filtration	Traps 99.9% of dust and allergens, ideal for allergy sufferers
Motorized Brush Roll	Automatically adjusts between carpets and hard floors; can be turned off for delicate rugs
Swivel Steering	Provides full maneuverability around furniture and obstacles
Easy-Empty Dust Cup	One-touch release for hygienic disposal without touching debris
Attachments	Crevice tool, dusting brush, and upholstery tool for above-floor cleaning
Cleaning Modes	CARPET, HARD FLOOR, and OFF settings for brush roll control
Wand Release	Quick-release button to convert to handheld vacuum
Cord Wrap	Integrated hooks for neat power cord storage
Headlight	LED light illuminates dark areas under furniture

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

Attach the handle: Insert handle into main body until it clicks securely into place.
Connect the hose: Attach hose to the port on the back of the vacuum; ensure it is fully seated.
Install attachments: Store crevice tool, dusting brush, and upholstery tool on the provided caddy or dock.
Check filters: Ensure HEPA filter and pre-motor filter are properly installed (see Maintenance section).

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Plug in the vacuum; select appropriate cleaning mode.

Power on: Press the foot pedal or power button (model dependent) to start suction.
Select floor type: Use the brush roll switch to select CARPET, HARD FLOOR, or OFF (for delicate rugs).
Begin vacuuming: Push vacuum forward and back in slow, overlapping strokes.
Empty dust cup: When full, press release button to detach and empty into trash.

CAUTION! Do not vacuum large objects, liquids, or hot ashes. Keep hair and loose clothing away from brush roll.

Specifications

Model: Shark UVC805C Upright Vacuum Cleaner.
Power: 120V, 60Hz, 12 Amps.
Suction Power: Adjustable via floor selector.
Filtration: HEPA filter + foam pre-motor filter.
Cord Length: 25 feet.
Dust Cup Capacity: 1.2 dry quarts.
Weight: 14.5 lbs.
Warranty: 5-year limited warranty (see manual for details).
Attachments Included: Crevice tool, dusting brush, upholstery tool.

Controls and Settings

Main controls located on handle and foot of vacuum.

Handle: Power button (on some models), wand release button, hose release.

Floor Nozzle: Brush roll switch (CARPET/HARD FLOOR/OFF), headlight (auto-on).

Settings: Suction power is automatic based on floor setting. Use OFF setting for area rugs or hard floors where brush roll may scatter debris. Wand release converts vacuum to handheld mode for above-floor cleaning.

Using Attachments

For above-floor cleaning: detach wand and connect desired tool.

Turn off and unplug vacuum before changing attachments.
Press wand release button to detach handle and wand assembly.
Connect crevice tool, dusting brush, or upholstery tool to end of wand.
Plug in vacuum and use power button on handle (if equipped) or main power control.

Tip: Use crevice tool for tight spaces; dusting brush for shelves and blinds; upholstery tool for furniture and stairs.

Cleaning Modes

Three brush roll settings optimize cleaning for different surfaces.

CARPET Mode: Brush roll spins at high speed to lift dirt and pet hair from carpets.
HARD FLOOR Mode: Brush roll spins slower to avoid scattering debris on hard surfaces.
OFF Mode: Brush roll stops completely; use for delicate rugs or hard floors where suction-only cleaning is preferred.

WARNING! Do not use CARPET mode on hard floors without area rugs, as it may scatter debris. Always turn off vacuum before changing modes.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Empty dust cup: Empty after each use or when full. Press release button, remove cup, and empty into trash.
Clean filters: Rinse HEPA filter and pre-motor filter under cold water every 3 months. Air dry completely for 24 hours before reinstalling.
Clear brush roll: Regularly remove hair and fibers wrapped around brush roll. Use scissors if necessary.
Check for clogs: If suction decreases, check hose, wand, and nozzle for blockages.

CAUTION! Always unplug vacuum before maintenance. Do not use damaged filters or operate with wet filters.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. Copyright © SharkNinja Operating LLC. Shark and HEPA are trademarks of SharkNinja. For support, visit sharkclean.com or call 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup, clog, or dirty filter	Empty dust cup; check hose and nozzle for blockages; clean or replace filters.
Brush roll not spinning	Mode set to OFF; tangled debris	Switch to CARPET or HARD FLOOR mode; clear hair and fibers from brush roll.
Vacuum won't turn on	Power cord not plugged in; tripped overload protector	Ensure plug is secure; wait 45 minutes for motor to cool if overload protector engaged.
Unusual noise	Foreign object in brush roll or hose	Turn off and unplug; inspect brush roll and hose; remove obstruction.
Dust escaping from vacuum	Filter not installed properly; dust cup not sealed	Ensure filters are correctly seated; check that dust cup is locked in place.

Reset: Unplug for 45 minutes to reset thermal overload protector.

Service: 1-800-798-7398; sharkclean.com