Shark UV204 Vacuum Cleaner Manual

The Shark UV204 is a powerful upright vacuum cleaner featuring UV sanitization technology, HEPA filtration, multi-surface cleaning capabilities, adjustable height settings, a motorized brushroll, and a large-capacity dust cup. It is designed for deep cleaning carpets and hard floors while reducing allergens. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes & Attachments 7. UV Sanitization Feature 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Upright vacuum body with UV light module, Motorized brushroll, HEPA filter, Large dust cup with easy-empty mechanism, Handle with controls, Hose and wand assembly, Cleaning attachments.

Feature	Description
UV Sanitization Light	Kills germs and bacteria on surfaces as you clean
HEPA Filtration System	Traps 99.9% of dust and allergens
Motorized Brushroll	Deep cleans carpets and agitates embedded dirt
Multi-Surface Settings	Adjustable height for carpets and hard floors
Large Dust Cup	Easy-empty, bagless design
Attachments Included	Crevice tool, upholstery tool, dusting brush
Power Switch	Turns vacuum and UV light on/off
Brushroll On/Off	Disengages brushroll for delicate floors
Height Adjustment Lever	Changes cleaning head height
Wand Release Button	Detaches hose and wand for above-floor cleaning

Assembly & Setup

Unpack and inspect all parts. Assemble on a flat surface.

Attach handle: Insert handle into body until it clicks securely.
Install wand: Insert wand into hose port and twist to lock.
Attach hose: Connect hose to wand and body ports.
Install filters: Place HEPA filter in rear compartment; ensure pre-motor filter is seated.
Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching.

First-Time Use

Plug in vacuum; follow these steps for initial operation.

Select floor setting: Use height adjustment lever for carpet or hard floor.
Turn on power: Press power switch; UV light will illuminate (if enabled).
Begin vacuuming: Push vacuum forward and back in slow, overlapping strokes.
Empty dust cup: Press release button and empty when full.
Use attachments: Detach wand for above-floor cleaning; select appropriate tool.

CAUTION! Keep UV light away from eyes and skin. Do not use on wet surfaces.

Specifications

Model: Shark UV204 Upright Vacuum.
Power: 120V, 60Hz, 12 Amps.
Filtration: HEPA filter with pre-motor foam filter.
Dust Cup Capacity: 1.5 liters.
Cord Length: 25 feet.
UV Light:Germicidal UV-C technology.
Attachments: Crevice tool, upholstery tool, dusting brush.
Weight: 15 lbs.
Warranty: 5-year limited warranty.

Controls and Settings

Main controls located on handle. Power Switch: Turns vacuum and UV light on/off. Brushroll Switch: Turns brushroll on for carpets, off for hard floors. Height Adjustment: Lever with multiple settings (Low Pile, High Pile, Hard Floor). Wand Release: Button to detach hose and wand. Dust Cup Release: Button to remove dust cup for emptying.

Settings Overview: Use low height for bare floors and thin carpets; medium for standard carpets; high for thick carpets. Disable brushroll when cleaning delicate rugs or hard floors to prevent scattering debris.

Cleaning Modes & Attachments

Upright Mode: For floor cleaning. Above-Floor Mode: Use wand and attachments.

Turn off vacuum before switching modes.
Press wand release button and pull wand out.
Attach desired tool: Crevice tool for tight spaces; upholstery tool for furniture; dusting brush for surfaces.
Select suction setting if available.

Tip: Clear area of large debris before vacuuming to prevent clogs.

UV Sanitization Feature

UV light kills germs on surfaces as you vacuum.

Ensure UV feature is enabled (default on with power).
Vacuum slowly to allow UV exposure time.
Keep UV light close to surface but not touching.
Do not look directly at UV light; avoid skin exposure.
Turn off UV light via power switch if not needed.

WARNING! UV light is for surface sanitization only. Not a substitute for disinfection chemicals. Keep away from children and pets.

Care & Maintenance

Unplug before maintenance. Regular cleaning ensures performance.

Empty dust cup after each use.
Clean filters monthly: Tap HEPA filter; wash foam filter with water, air dry completely.
Check brushroll for tangles; cut away hair and strings with scissors.
Inspect hose for clogs; use long object to clear obstructions.
Wipe exterior with dry cloth; no liquids.

CAUTION! Do not operate without filters. Ensure all parts are dry before reassembly.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. UV-C light emits ultraviolet radiation; follow safety instructions. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power cord/outlet	Check plug connection; try different outlet; ensure power switch is on.
Loss of suction	Full dust cup/clog	Empty dust cup; check hose, wand, and brushroll for blockages.
Brushroll not spinning	Tangled debris/switch	Turn off, unplug, and clear brushroll; ensure brushroll switch is on.
UV light not working	Bulb/connection	Ensure power is on; check bulb; contact service if damaged.
Overheating	Clogged filters/full dust cup	Clean filters; empty dust cup; let vacuum cool for 30 minutes.

Reset: Unplug for 10 minutes; restart.

Service: 1-800-798-7398; www.sharkclean.com