Shark UV180 Vacuum Cleaner Manual

The Shark UV180 is a powerful upright vacuum cleaner featuring UV-C sanitizing technology, HEPA filtration, multi-surface brushroll, lift-away canister mode, and advanced swivel steering. Designed for deep cleaning on carpets and hard floors while neutralizing common household allergens and bacteria. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: UV-C sanitizing head, HEPA filter system, lift-away canister, swivel steering handle, brushroll on/off switch, dust cup release button.

Assembly & Setup

Unpack and inspect all components. Assemble on a flat, stable surface.

1. Attach handle: Insert handle into main body until it clicks securely into place.
2. Install HEPA filter: Remove filter compartment cover, insert HEPA filter, replace cover.
3. Attach hose: Connect hose to the main body and lift-away canister ports.
4. Install cleaning tools: Store crevice tool, dusting brush, and upholstery tool in built-in storage.
5. Plug into AC power outlet.

WARNING! Ensure all parts are securely connected before use. Keep fingers away from moving parts during assembly.

First-Time Use

Before first use, perform a test run in an open area.

1. Power on: Press power switch; ensure UV-C light illuminates (blue indicator).
2. Adjust height: Set appropriate height for your floor type (low for hard floors, higher for carpets).
3. Test brushroll: Engage brushroll for carpets; turn off for hard floors or delicate rugs.
4. Test lift-away mode: Press release button to detach canister for above-floor cleaning.
5. Empty dust cup: After initial use, empty dust cup to ensure optimal suction.

CAUTION! Do not look directly at UV-C light. Keep vacuum away from water and liquids.

Specifications

• Model: Shark UV180 Upright Vacuum Cleaner.
• Technology: UV-C sanitizing with HEPA filtration.
• Power Source: 120V AC, 60Hz, 12 Amps.
• Cord Length: 25 feet retractable power cord.
• Dust Cup Capacity: 1.5 dry quarts.
• Filtration: Sealed system with HEPA filter.
• Brushroll: Multi-surface, self-adjusting.
• Cleaning Modes: Upright and lift-away canister modes.
• Weight: 15.2 lbs.
• Warranty: 5-year limited warranty.

Controls and Settings

Main controls located on handle and body. Handle: Power switch, brushroll on/off, height adjustment lever. Body: Dust cup release, UV-C indicator light, accessory release buttons.

Indicator Lights: Blue light indicates UV-C is active; red light indicates filter needs cleaning or replacement.

Height Adjustment: 5 settings from lowest (hard floors) to highest (thick carpets). Brushroll Control: On for carpets; off for hard floors and delicate area rugs. Power Settings: Standard and boost modes for extra suction power.

Cleaning Modes

Upright Mode: For floor cleaning with UV-C sanitizing active. Lift-Away Mode: Detach canister for stairs, furniture, and above-floor cleaning.

1. Select mode based on cleaning needs (floors vs. above-floor).
2. For upright mode: Ensure canister is locked in place.
3. For lift-away mode: Press release button and lift canister away from main body.
4. Attach appropriate tool: Use crevice tool, dusting brush, or upholstery tool as needed.

Tip: Use lift-away mode with attachments for detailed cleaning of curtains, blinds, and auto interiors.

UV-C Sanitizing Technology

UV-C light neutralizes microorganisms as you clean.

1. Ensure UV-C light is on (blue indicator visible).
2. Move vacuum slowly over surfaces to allow sufficient exposure time.
3. UV-C works in both upright and lift-away modes when powered on.
4. Light automatically turns off when vacuum is powered off or tilted beyond 45 degrees.

WARNING! Do not stare directly at UV-C light. Keep vacuum away from children and pets during operation. UV-C is not a substitute for chemical disinfection.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

1. Empty dust cup: After each use or when full; press release button to remove.
2. Clean filters: Rinse HEPA filter every 3 months (air dry completely before reinserting).
3. Check brushroll: Monthly remove hair and debris wrapped around brushroll.
4. Inspect UV-C bulb: Replace annually or if blue light stops illuminating.
5. Clean exterior: Use dry cloth only; no liquids or cleaning agents.

CAUTION! Unplug vacuum before performing any maintenance. Ensure all parts are completely dry before reassembly.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. UL Listed for safety. Copyright © SharkNinja Operating LLC. UV-C technology patent pending. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug for 10 minutes if vacuum overheats or malfunctions.

Service: 1-800-798-7398; www.sharkclean.com