Shark UltraLight PowerFins QS700HGN Vacuum Cleaner Manual

The Shark UltraLight PowerFins QS700HGN is a lightweight, corded upright vacuum cleaner featuring PowerFins technology for deep carpet cleaning, Anti-Allergen Complete Seal technology, a LED headlight, a large-capacity dust cup, and a versatile cleaning wand with attachments. It is designed for powerful suction and multi-surface cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main vacuum body with PowerFins brushroll, Handle with controls, Dust Cup, Cleaning Wand, Crevice Tool, Upholstery Tool, Pet Multi-Tool.

Assembly & Setup

Unpack and inspect all contents. Assemble before first use.

1. Attach the Handle: Align the handle with the main body until it clicks into place.
2. Install the Dust Cup: Ensure it is securely locked into position.
3. Attach the Hose and Wand: Connect the hose to the port on the back of the vacuum. Insert the wand into the hose until it clicks.
4. Store Attachments: Attach the crevice tool, upholstery tool, and pet multi-tool to the accessory clips on the wand or vacuum body.
5. Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Check that all parts are securely connected.

First-Time Use

Plug in the vacuum and familiarize yourself with the controls.

1. Select Floor Type: Use the Power/Floor Selector switch on the handle. Set to "CARPET" for carpets and rugs, or "HARD FLOOR" for hard surfaces.
2. Turn On: Press the power button on the handle.
3. Adjust Height (if applicable): The vacuum may automatically adjust. For manual models, ensure the setting matches your carpet pile.
4. Begin Cleaning: Push the vacuum forward and back in slow, overlapping strokes.
5. Use Attachments: To clean above floors, detach the wand and attach the desired tool.

CAUTION! Keep the vacuum cord away from the brushroll and moving parts. Do not vacuum large, hard objects.

Specifications

• Model: Shark UltraLight PowerFins QS700HGN
• Type: Corded Upright Vacuum
• Technology: PowerFins Brushroll, Anti-Allergen Complete Seal
• Dust Cup Capacity: 1.0 Dry Quarts
• Cord Length: 25 feet
• Attachments: Cleaning Wand, Crevice Tool, Upholstery Tool, Pet Multi-Tool
• Filters: Washable Foam and Felt Filters
• Power Source: 120V AC, 60Hz
• Weight: Approximately 10 lbs
• Warranty: Limited 5-year warranty (see manual for details)

Controls and Parts

Main controls are located on the handle. Body Parts: PowerFins brushroll, Dust Cup release button, Handle release pedal, Cord hook.

Handle Controls: Power Button, Power/Floor Selector (Carpet/Hard Floor).

Attachments: Connect to the wand or storage clips. Hose: Extends for above-floor cleaning. Filters: Located in the dust cup lid and behind it; washable. Brushroll: Accessible from the bottom for cleaning and maintenance.

Cleaning Modes & Attachments

Upright Mode: For carpets and large floor areas. Handheld Mode: Detach the wand and attach a tool for stairs, furniture, and tight spaces.

1. For Carpets: Use the "CARPET" setting. The PowerFins will engage for deep cleaning.
2. For Hard Floors: Use the "HARD FLOOR" setting to reduce suction and prevent scattering debris.
3. Above-Floor Cleaning: Detach the wand by pressing the release button. Attach the Crevice Tool for tight spaces, Upholstery Tool for furniture, or Pet Multi-Tool for pet hair.
4. Under Furniture: Press the handle release pedal to recline the vacuum low to the ground. The LED headlight will activate.

Tip: Regularly check and clean the brushroll to maintain optimal performance.

Emptying the Dust Cup

Empty the dust cup when it reaches the "MAX" fill line.

1. Turn off and unplug the vacuum.
2. Press the Dust Cup Release button and lift the cup away from the vacuum body.
3. Hold the dust cup over a trash can. Press the bottom release latch to open the door, allowing debris to fall out.
4. Close the door securely. You may tap the filter gently to dislodge fine dust.
5. Reinsert the dust cup into the vacuum until it clicks into place.

WARNING! Always unplug the vacuum before emptying. Do not use if the dust cup is not properly sealed.

Maintenance & Filter Care

For optimal performance, clean filters monthly and check the brushroll regularly.

1. Washable Filters: Remove the foam and felt filters from the dust cup lid. Rinse under lukewarm water until water runs clear. Let air dry for at least 24 hours completely before reinstalling.
2. Brushroll Maintenance: Turn the vacuum over. Use scissors or a seam ripper to carefully cut and remove any wrapped hair, strings, or debris from the brushroll ends and fins.
3. Check for Blockages: If suction is reduced, check the hose, wand, and air pathways for clogs.

CAUTION! Do not operate the vacuum without all filters installed and completely dry. Never immerse the main body, handle, or hose in water.

Storage

Store in a cool, dry place.

1. Wrap the power cord around the cord hooks on the back of the vacuum.
2. Attach the cleaning wand and tools to the storage clips.
3. Stand the vacuum upright. Avoid storing it on its side for long periods.

Tip: Empty the dust cup and clean the filters before long-term storage.

Regulatory Information

This appliance complies with FCC Part 15 Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © SharkNinja Operating LLC. Shark, UltraLight, and PowerFins are trademarks of SharkNinja. For support, visit sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug the vacuum for 60 seconds, then plug back in.

Service: 1-800-798-7398; sharkclean.com