Shark SV780_N 14 Vacuum Cleaner Manual

The Shark SV780_N 14 is a powerful 14-inch corded upright vacuum cleaner featuring a multi-surface brushroll, advanced swivel steering, HEPA filtration, multiple cleaning modes, a large-capacity dust cup, and a suite of onboard tools for above-floor cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes & Attachments 7. Emptying & Cleaning the Dust Cup 8. Filter Maintenance 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Motorized brushroll, Swivel steering head, HEPA filter system, Onboard hose and tools, Large-capacity dust cup with quick-release, Cord wrap hooks.

Feature	Description
Multi-Surface Brushroll	Automatically adjusts between carpets and hard floors
Advanced Swivel Steering	Provides tight maneuverability around furniture
HEPA Filtration System	Captures 99.9% of dust and allergens
Large Capacity Dust Cup	Easy-to-empty, bagless design
Cleaning Modes	Upright, Handheld, and Above-Floor modes
Onboard Tools	Includes crevice tool, dusting brush, and upholstery tool
Power Cord	25-foot cord with wrap hooks
Brushroll On/Off	Switch to deactivate brushroll for hard floors
Suction Control	Adjustable for different surfaces
Wand Release	Button to detach wand for above-floor cleaning

Assembly & Setup

Unpack and inspect all contents. Assemble before first use.

Attach the handle: Align the handle with the body until it clicks into place.
Install the hose: Connect the hose end to the port on the vacuum body.
Attach the wand: Insert the wand into the hose grip until secure.
Mount the tools: Clip the crevice tool and dusting brush onto the designated storage clips.
Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Handle with care to avoid pinching.

First-Time Use

Before cleaning, perform a quick setup check.

Check filters: Ensure both pre-motor and HEPA filters are properly installed.
Inspect brushroll: Remove any packaging material or debris from the brushroll area.
Select mode: For floor cleaning, ensure the vacuum is in upright mode. For above-floor cleaning, detach the wand.
Adjust height: For thick carpets, set the height adjustment to the highest setting.
Power on: Plug in, press the power foot switch, and begin cleaning.

CAUTION! Keep hair, loose clothing, fingers, and feet away from openings and moving parts.

Specifications

Model: Shark SV780_N 14.
Power Source: 120V AC, 60Hz, Corded.
Cord Length: 25 feet.
Dust Cup Capacity: 1.5 dry quarts.
Filtration: HEPA filter system.
Cleaning Path: 14 inches.
Swivel Steering: 180-degree pivot.
Weight: 15 lbs.
Included Tools: Crevice tool, dusting brush, upholstery tool.
Warranty: 5-year limited warranty.

Controls and Settings

Main controls located on the handle and body.

Handle: Power switch (on handle grip), Suction control slider, Brushroll on/off switch.

Body: Wand release button, Dust cup release latch, Hose release button.

Settings: Suction control (High/Low for delicate rugs), Brushroll on/off (for hard floors vs carpets), Height adjustment (manual lever for carpet pile).

Cleaning Modes & Attachments

Three primary cleaning modes: Upright, Handheld, and Above-Floor.

Upright Mode: For carpets and large floor areas. Use the power foot switch.
Above-Floor Mode: Press the wand release button to detach the wand and hose. Attach tools for cleaning furniture, ceilings, and stairs.
Handheld Mode: Detach the pod from the main body by pressing the release latch. Use for quick spot cleaning.

Tip: Turn off the brushroll when cleaning hard floors to prevent scattering debris.

Emptying & Cleaning the Dust Cup

Empty the dust cup when it reaches the MAX fill line.

Unplug the vacuum.
Press the dust cup release latch and lift the cup away from the body.
Hold over a trash can and press the bottom release to open the door.
Tap gently to remove all debris.
Close the door and reattach the dust cup until it clicks.

WARNING! Always unplug before emptying. Do not use water or liquids to clean the dust cup.

Filter Maintenance

Regular filter maintenance ensures peak performance.

Pre-Motor Foam Filter: Rinse with cold water every 3 months. Air dry completely for 24 hours before reinstalling.
HEPA Filter: Replace every 12-18 months under normal use. Do not wash.
To access filters, remove the dust cup. The filters are located in the compartment behind it.

CAUTION! Never operate the vacuum without all filters installed and completely dry.

Care & Storage

Unplug and cool down before storage. Wrap the power cord around the hooks on the back. Store in a dry, indoor location. Clean the brushroll regularly by cutting away wrapped hair and fibers with scissors.

CAUTION! Do not store near heat sources. Keep the vacuum and cord away from sharp edges.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B. For your safety, this equipment has been tested and found to comply with the limits for a Class B digital device. Copyright © SharkNinja Operating LLC. Shark is a registered trademark. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	No power / faulty outlet	Check outlet; ensure plug is secure; try a different circuit.
Loss of suction	Full dust cup / clog	Empty dust cup; check hose, wand, and tools for blockages.
Brushroll not spinning	Obstruction / belt	Unplug and remove debris from brushroll ends; inspect belt for wear.
Vacuum is overheating	Clogged filter / blockage	Unplug and let cool. Clean filters and check for obstructions in air path.
Unusual noise	Foreign object in air path	Unplug and inspect brushroll, hose, and inlet for obstructions.

Reset: Unplug for 60 minutes to reset thermal protector if unit overheats.

Service: 1-800-798-7398; www.sharkclean.com