Shark SV719 Vacuum Cleaner Manual

The Shark SV719 is a versatile upright vacuum cleaner designed for deep cleaning on multiple surfaces. It features a powerful motor, advanced swivel steering, a lift-away pod for portable cleaning, HEPA filtration, multiple brush rolls, and various attachments for above-floor cleaning. Below are key sections covering safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Upright body with lift-away pod, motorized brush roll, swivel steering, dust cup, HEPA filter, crevice tool, dusting brush, upholstery tool, and power cord.

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

1. Attach handle: Insert handle into upright body until it clicks securely.
2. Install dust cup: Align and push into place until locked.
3. Attach hose: Connect hose to pod and secure clips.
4. Attach wand: Insert wand into hose connector.
5. Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching.

First-Time Use

Before cleaning, perform initial setup.

1. Check filters: Ensure HEPA and pre-motor filters are installed.
2. Adjust height: Set carpet height selector based on floor type.
3. Test brush roll: Turn on and verify brush roll spins freely.
4. Test attachments: Connect each to ensure proper fit.
5. Empty dust cup: Ensure it is empty before first use.

CAUTION! Keep hair, loose clothing, and fingers away from brush roll.

Specifications

• Model: Shark SV719.
• Type: Upright with lift-away pod.
• Motor: Powerful suction with adjustable settings.
• Filtration: HEPA filter with anti-allergen seal.
• Cord Length: 25 feet.
• Dust Cup Capacity: 1.5 dry quarts.
• Brush Roll: Motorized with on/off control.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Power Source: 120V AC, 60Hz.
• Weight: 15 lbs.

Controls and Settings

Main controls located on handle and body.

Handle: Power switch, brush roll on/off button, suction control slider.

Body: Carpet height adjuster (low, medium, high), dust cup release button, hose release latch.

Settings: Suction power (low for delicate rugs, high for carpets), brush roll on/off (for hard floors), height adjustment for carpet pile.

Using Attachments

For above-floor cleaning, detach pod or use hose.

1. Detach pod: Press release button and lift away from upright.
2. Connect tool: Insert desired attachment into wand or hose end.
3. Select suction: Use low setting for delicate surfaces.
4. Clean: Move attachment over surface slowly.
5. Reattach: Return pod to upright until it clicks.

Tip: Store attachments on caddy or wall mount for easy access.

Cleaning Different Surfaces

Adjust settings based on floor type.

1. Carpets: Set height to match pile; brush roll ON.
2. Hard floors: Brush roll OFF to prevent scattering debris.
3. Area rugs: Use low suction and brush roll ON.
4. Stairs: Use lift-away pod with upholstery tool.
5. Furniture: Use dusting brush or upholstery tool on low suction.

WARNING! Do not vacuum wet surfaces or large objects that may damage motor.

Maintenance & Care

Regular maintenance ensures optimal performance.

1. Empty dust cup: Press release button; empty when full.
2. Clean filters: Rinse HEPA and pre-motor filters monthly; air dry 24 hours.
3. Clear brush roll: Remove hair and debris regularly.
4. Check hose: Remove clogs if suction decreases.
5. Inspect cord: Do not use if damaged.

CAUTION! Unplug before maintenance. Do not use water on motor or electrical parts.

Regulatory Information

FCC Part 15: Class B device; complies with interference limits. Copyright © SharkNinja Operating LLC. For support, visit www.sharkclean.com or contact 1-800-798-7398. This product is covered by a limited warranty; see manual for details.

Troubleshooting

Reset: Unplug for 60 seconds if motor overheats.

Service: 1-800-798-7398; www.sharkclean.com