Shark SV1106 Vacuum Cleaner Manual

The Shark SV1106 is a versatile upright vacuum cleaner designed for deep cleaning carpets and hard floors. It features powerful suction, a HEPA filtration system, multiple cleaning modes, a motorized brushroll, LED headlights, and a lightweight, maneuverable design. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Motorized brushroll, HEPA filter, LED headlights, Dust cup with easy-empty mechanism, Handle with controls, Hose and wand assembly, Cleaning attachments.

Assembly Instructions

Unpack and inspect all parts. Assemble on a flat surface.

1. Attach the handle: Align handle with body and push until it clicks into place.
2. Install the wand: Insert wand into hose connector until secure.
3. Attach cleaning tools: Store tools on holder or attach to wand as needed.
4. Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid injury.

First-Time Setup

Plug in vacuum; perform initial check.

1. Check brushroll: Ensure it rotates freely and is free of obstructions.
2. Install filters: Place HEPA and pre-motor filters in their compartments.
3. Select cleaning mode: Use mode selector switch for carpet or hard floor.
4. Test suction: Turn on vacuum to verify proper operation.

CAUTION! Keep hair, loose clothing, and fingers away from brushroll while operating.

Specifications

• Model: Shark SV1106 Upright Vacuum.
• Power Source: 120V AC, 60Hz.
• Cord Length: 25 feet.
• Dust Cup Capacity: 1.5 liters.
• Filtration: HEPA filter with anti-allergen seal.
• Cleaning Modes: Carpet, Hard Floor, Bare Floor.
• Brushroll: Motorized, self-cleaning.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Weight: 12.5 lbs.
• Warranty: 5-year limited warranty.

Controls and Settings

Power switch on handle. Mode selector on body. Wand release pedal near base.

Handle Controls: POWER ON/OFF, Suction control slider.

Cleaning Modes: CARPET (brushroll on), HARD FLOOR (brushroll on, reduced suction), BARE FLOOR (brushroll off). Suction Control: Adjust suction power for different surfaces. Brushroll On/Off: Turn off for delicate rugs or hard floors.

Cleaning Modes & Attachments

Use appropriate mode for surface type. Attach tools for above-floor cleaning.

1. Turn off vacuum before changing modes or attachments.
2. Select mode: Use selector switch for carpet, hard floor, or bare floor.
3. Attach tools: Connect crevice tool, dusting brush, or upholstery tool to wand.
4. Use wand release: Step on pedal to detach wand for above-floor cleaning.

Tip: For best results, make slow, overlapping passes.

Maintenance & Care

Regular maintenance ensures optimal performance.

1. Empty dust cup: When full or after each use.
2. Clean filters: Wash every 3 months or as needed.
3. Check brushroll: Remove hair and debris regularly.
4. Inspect hose and wand: Clear any blockages.
5. Store properly: Wrap cord around hooks, store in dry place.

WARNING! Unplug vacuum before performing any maintenance.

Emptying the Dust Cup

Empty when dust reaches MAX line.

1. Turn off and unplug vacuum.
2. Press dust cup release button.
3. Hold over trash can and press bottom release to open.
4. Close securely and reattach to vacuum.

CAUTION! Avoid inhaling dust. Empty outdoors if possible.

Filter Cleaning

Wash filters every 3 months for best performance.

1. Remove filters: Open filter compartment, take out HEPA and pre-motor filters.
2. Rinse: Use cold water only; no soap or detergents.
3. Dry: Air dry completely for 24 hours before reinstalling.
4. Reinstall: Ensure filters are seated properly.

WARNING! Never operate vacuum without filters installed.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug for 30 minutes if overheating occurs.

Service: 1-800-798-7398; www.sharkclean.com