Shark Pursuit UV209 Vacuum Cleaner Manual

The Shark Pursuit UV209 is a powerful upright vacuum cleaner featuring UV sanitization technology, HEPA filtration, multi-surface cleaning capabilities, LED headlights, and a lightweight yet durable design. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes & Attachments 7. UV Sanitization Feature 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: UV sanitization module, HEPA filter system, motorized brush roll, LED headlights, telescopic wand, dust cup with one-touch release, and multiple cleaning attachments.

Feature	Description
UV Sanitization	Ultraviolet light kills germs and bacteria on surfaces
HEPA Filtration	Captures 99.9% of dust and allergens
Motorized Brush Roll	Deep cleans carpets and hard floors
LED Headlights	Illuminates dark areas under furniture
Telescopic Wand	Adjustable length for comfortable use
One-Touch Dust Cup	Easy empty release mechanism
Multi-Surface Settings	Adjustable suction for carpets and hard floors
Attachments Included	Crevice tool, upholstery brush, dusting brush
Power Switch	Main power control with indicator light
UV Mode Button	Activates/deactivates UV sanitization

Assembly & Setup

Unpack and inspect all components. Assemble on a clean, flat surface.

Attach handle: Insert handle into main body until it clicks securely.
Install telescopic wand: Extend wand to desired length and lock in place.
Attach cleaning head: Connect cleaning head to wand until it locks.
Install HEPA filter: Remove filter compartment cover, insert filter, replace cover.
Plug into AC power outlet.

WARNING! Ensure all parts are securely connected before use. Do not force connections.

First-Time Use

Before first use, perform initial setup and test functions.

Power on: Press power switch; LED indicator should illuminate.
Test suction: Place hand over nozzle to feel suction power.
Test UV feature: Press UV button; blue light should activate (do not look directly at UV light).
Adjust height: Set cleaning head to appropriate height for floor type.
Perform test clean on small area.

CAUTION! Keep UV light away from eyes and skin. Never operate without filter installed.

Specifications

Model: Shark Pursuit UV209
Power: 120V AC, 60Hz, 12 Amps
Suction Power: 200 Air Watts
Filtration: HEPA filter (captures 99.9% of particles 0.3 microns+)
UV Technology: UV-C light at 254nm wavelength
Cord Length: 25 feet
Dust Cup Capacity: 1.2 liters
Weight: 12.5 lbs
Warranty: 5-year limited warranty
Operating Time: Continuous use up to 60 minutes

Controls and Settings

Main controls located on handle: Power switch, UV mode button, suction adjustment dial.

Power Switch: Turns vacuum on/off with LED indicator.

UV Mode Button: Press to activate UV sanitization (blue light indicator). Press again to deactivate.

Suction Adjustment Dial: Three settings: MAX (carpets), MED (hard floors), MIN (delicate surfaces).

Height Adjustment: Lever on cleaning head adjusts for carpet pile height.

Brush Roll On/Off: Switch on cleaning head for hard floor protection.

Cleaning Modes & Attachments

Multiple cleaning configurations for different surfaces.

Upright Mode: For floor cleaning with motorized brush roll.
Above-Floor Mode: Detach wand for stairs, furniture, ceilings.
Crevice Tool: For tight spaces, corners, edges.
Upholstery Brush: For sofas, chairs, car interiors.
Dusting Brush: For delicate surfaces, blinds, shelves.

Tip: Turn off brush roll when cleaning hard floors to prevent scattering debris.

UV Sanitization Feature

UV-C light eliminates up to 99.9% of bacteria and germs on surfaces.

Activate UV: Press UV button while vacuum is on.
Move slowly: Pass over each area for 3-5 seconds for effective sanitization.
Deactivate: Press UV button again or turn off vacuum.
Safety features: Automatic shutoff if vacuum is lifted more than 2 inches from surface.

WARNING! Never look directly at UV light. Keep away from children and pets. UV light is most effective on hard, non-porous surfaces.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Empty dust cup: Press release button when cup is 2/3 full.
Clean filters: Wash pre-motor filter monthly, HEPA filter every 3 months.
Check brush roll: Remove hair and debris weekly.
Inspect UV bulb: Replace annually or if blue light dims.
Clean exterior: Use dry cloth only; no liquids.

CAUTION! Unplug before maintenance. Allow filters to dry completely before reinstalling.

Regulatory Information

FCC Part 15: Class B digital device compliant. UL listed for safety. UV component complies with FDA 21 CFR 1040.10. Copyright © 2025 SharkNinja Operating LLC. All rights reserved. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup/clog	Empty dust cup; check for clogs in hose and wand.
UV light not working	Bulb/connection	Check bulb; ensure vacuum is on surface; replace if needed.
Brush roll not spinning	Obstruction/setting	Remove debris from brush roll; ensure brush roll is ON.
Overheating	Filter/clog	Clean filters; check for obstructions; allow to cool 60 minutes.
Unusual noise	Foreign object	Turn off immediately; check for objects in brush roll or hose.

Reset: Unplug for 10 minutes, then restart.

Service: 1-800-798-7398; www.sharkclean.com