Shark Powered Lift-Away NV681UKT Vacuum Cleaner Manual

The Shark Powered Lift-Away NV681UKT is a versatile upright vacuum cleaner featuring a detachable pod for portable cleaning, advanced swivel steering, a HEPA filter, multiple brushroll settings for carpets and hard floors, a large-capacity dust cup, and various attachments for above-floor cleaning. Below are key sections covering safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main vacuum body with motor, Detachable Lift-Away pod, Swivel steering handle, Hose and wand, Dust cup with HEPA filter, Brushroll with settings, On-board accessory storage.

Assembly & Setup

Unpack all parts and inspect for damage. Assemble on a flat surface.

1. Attach handle: Insert handle into main body until it clicks securely.
2. Connect hose: Attach hose to the port on the vacuum body.
3. Install wand: Insert wand into hose cuff until it locks.
4. Attach floor nozzle: Connect nozzle to the wand or main body as per mode.
5. Store attachments: Clip provided tools onto the onboard storage clips.

WARNING! Ensure all parts are securely connected before plugging in. Do not force connections.

First-Time Use

Plug into a standard electrical outlet. Select appropriate settings for your floor type.

1. For carpets: Ensure brushroll is engaged. Adjust carpet height if needed.
2. For hard floors: Turn brushroll off to prevent scattering debris.
3. To use Lift-Away mode: Press release button to detach pod; connect hose and desired attachment.
4. Empty dust cup: Press release button and empty when full or after each use.

CAUTION! Keep hair, loose clothing, and fingers away from brushroll and openings.

Specifications

• Model: NV681UKT Powered Lift-Away.
• Power: [Insert Wattage/Amperage] motor.
• Filtration: HEPA filter system.
• Dust Cup Capacity: [Insert Volume] liters.
• Cord Length: [Insert Length] feet/meters.
• Brushroll: Motorized with on/off control.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Power Source: 220-240V AC, 50Hz (UK).
• Weight: Approximately [Insert Weight] kg.

Controls and Settings

Main controls located on handle and body.

Handle: Power switch, Brushroll on/off button, Carpet height adjustment dial.

Body: Lift-Away release button, Dust cup release, Hose port, Wand release button.

Settings: Carpet height (Low/Medium/High), Brushroll (On for carpets, Off for hard floors), Suction power (single speed on this model). Use Lift-Away mode for stairs, upholstery, and above-floor cleaning.

Using Attachments

For detailed cleaning: Use attachments with the Lift-Away pod or hose.

1. Detach pod: Press release button and lift away.
2. Select attachment: Connect crevice tool, dusting brush, or upholstery tool to hose.
3. Clean: Use tool on stairs, curtains, furniture, or tight spaces.
4. Return to upright: Reattach pod by aligning and pressing down until it clicks.

Tip: Ensure hose is fully extended and not kinked for optimal suction.

Maintenance & Cleaning

Regular maintenance ensures peak performance.

1. Empty dust cup: After each use or when full. Press release button to remove.
2. Clean filter: Rinse HEPA filter under cold water every 3 months. Air dry for 24 hours completely before reinstalling.
3. Check brushroll: Regularly remove hair and debris wrapped around brushroll. Turn off and unplug vacuum first.
4. Inspect hose and wand: Clear any blockages.

WARNING! Always unplug vacuum before performing any maintenance. Do not use damaged parts.

Storage & Care

Store in a cool, dry place. Wrap cord around cord hooks.

CAUTION! Do not store with a wet filter. Keep vacuum away from heat sources and water.

Regulatory Information

Complies with relevant UK/EU safety and EMC directives. Copyright © SharkNinja Operating LLC. For support, visit www.sharkclean.co.uk or contact customer service at 0800 862 0453.

Troubleshooting

Reset: Unplug for 60 seconds, then plug back in.

Service: 0800 862 0453; www.sharkclean.co.uk