Shark POWERDETECT RV2800ZEUK Series Vacuum Cleaner Manual

The Shark POWERDETECT RV2800ZEUK Series is a powerful cordless vacuum cleaner featuring POWERDETECT technology for enhanced surface detection, DuoClean PowerFins brushroll for deep carpet cleaning and hard floor pickup, LED headlights, Anti-Hair Wrap technology, a large dust cup with easy-empty mechanism, multiple cleaning modes (Eco, Normal, Max), and compatibility with various Shark accessories. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main vacuum body, DuoClean PowerFins brushroll, POWERDETECT sensor head, LED headlights, Handle with trigger, Battery pack, Charging dock, Crevice tool, Dusting brush, Upholstery tool.

Assembly & Setup

Unpack and inspect all contents. Assemble before first use.

1. Insert the handle: Align the handle with the main body until it clicks into place.
2. Attach the floor nozzle: Connect the POWERDETECT floor nozzle to the vacuum wand or handle.
3. Install the battery: Slide the battery pack into the vacuum body until it locks.
4. Mount the charging dock: Use included screws to mount the dock on a wall near an outlet.
5. Place vacuum on dock: Ensure the charging contacts align for charging.

WARNING! Ensure the vacuum is powered off during assembly. Keep fingers away from moving parts.

First-Time Use

Fully charge the battery before first use.

1. Charging: Place the vacuum on the charging dock. The indicator light will illuminate.
2. Power on: Press the power trigger on the handle to start vacuuming.
3. Select mode: Use the mode button to cycle through Eco, Normal, and Max settings.
4. Begin cleaning: Push the vacuum forward on floors. The POWERDETECT sensor will adjust suction automatically.
5. Empty dust cup: Press the release button to detach and empty the dust cup when full.

CAUTION! Do not use on wet surfaces. Keep hair, loose clothing, and fingers away from brushroll.

Specifications

• Model Series: RV2800ZEUK (POWERDETECT).
• Power Source: Rechargeable Lithium-Ion Battery.
• Run Time: Up to 60 minutes (Eco mode), approx. 30 minutes (Normal), approx. 15 minutes (Max).
• Charging Time: Approximately 4 hours for full charge.
• Dust Cup Capacity: 0.8 Liters.
• Filters: Washable foam and felt filters.
• Noise Level: ≤ 80 dB(A).
• Weight: Approx. 3.2 kg (with battery).
• Included Accessories: Crevice tool, dusting brush, upholstery tool, charging dock.

Controls and Modes

Main controls located on the handle and body.

Handle: Power Trigger (press and hold to run), Mode Button (cycles Eco/Normal/Max), Battery Indicator LEDs.

Body: Dust Cup Release Button, Brushroll Access Button, Filter Access Cover.

Cleaning Modes: Eco (for extended cleaning on hard floors), Normal (balanced cleaning for daily use), Max (for deep cleaning carpets and concentrated messes). The POWERDETECT sensor automatically boosts power when transitioning from hard floors to carpets.

Using Accessories

Accessories attach to the wand or handle for above-floor cleaning.

1. Detach the floor nozzle: Press the wand release button.
2. Attach desired tool: Insert the crevice tool, dusting brush, or upholstery tool into the end of the wand or handle.
3. Select mode: Use Normal or Max mode for accessory cleaning.
4. Clean: Use the tool on furniture, stairs, ceilings, or tight spaces.
5. Store tools: Use the on-board storage clips on the vacuum body.

Tip: For best suction with tools, ensure the dust cup is not full and filters are clean.

Cleaning & Maintenance

Regular maintenance ensures optimal performance.

1. Empty dust cup: Press release button, remove cup, and empty into trash. Close lid securely.
2. Clean brushroll: Turn vacuum over, press brushroll access buttons, and remove roll. Clear any debris or hair.
3. Wash filters: Remove foam and felt filters every month. Rinse with cold water and air dry for 24 hours completely before reinstalling.
4. Check for blockages: Inspect wand, hose, and nozzle if suction decreases.
5. Wipe exterior: Use a dry cloth to clean the vacuum body.

WARNING! Always turn off and remove battery before maintenance. Do not use damaged parts.

Battery & Charging

Use only the provided battery and charger.

Charging: Place vacuum on dock; indicator light pulses during charge, stays solid when full. Battery Care: For longest life, store in a cool, dry place. Avoid complete discharge; recharge when battery is low. Disposal: Do not dispose of battery in household trash. Recycle according to local regulations.

Care & Storage

Store vacuum on the charging dock in a dry location. Keep away from heat sources and direct sunlight.

CAUTION! Do not store with a wet dust cup or filters. Ensure the vacuum is powered off and the battery is installed or removed for long-term storage.

Regulatory Information

This appliance complies with relevant EU directives and UK regulations. The crossed-out wheeled bin symbol indicates separate collection for electrical waste. For support, visit www.sharkclean.co.uk or contact SharkHelpline at 0800 862 0453. Copyright © SharkNinja Operating LLC. SHARK and POWERDETECT are trademarks of SharkNinja Operating LLC.

Troubleshooting

Reset: Remove battery for 60 seconds, then reinsert.

Service: 0800 862 0453; www.sharkclean.co.uk