Shark Navigator UV400 26 Vacuum Cleaner Manual

The Shark Navigator UV400 26 is an upright vacuum cleaner featuring a HEPA filter, UV sanitizing light, Anti-Allergen Complete Seal technology, Lift-Away functionality for portable cleaning, a motorized brushroll for carpets and hard floors, a large dust cup capacity, multiple attachments, and a swivel steering head. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Upright vacuum body with Lift-Away pod, motorized floor nozzle, UV sanitizing light, HEPA filter, dust cup, hose, wand, and accessory attachments.

Assembly & Setup

Unpack and inspect all contents. Assemble on a flat, stable surface.

1. Attach the handle: Insert the handle into the main body until it clicks into place.
2. Connect the hose: Attach the hose to the designated port on the vacuum body.
3. Install the wand: Insert the wand into the hose grip until secure.
4. Attach floor nozzle: Align the floor nozzle with the base and push until it clicks.
5. Insert filters: Place the HEPA filter and pre-motor filter into their respective compartments.
6. Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Keep fingers away from moving parts.

First-Time Use

Before first use, ensure all filters are installed and the dust cup is empty.

1. Power on: Press the power button located on the handle.
2. Select floor type: Use the floor selector switch to match your surface (carpet/hard floor).
3. Engage UV light: Press the UV button to activate the sanitizing light (ensure nozzle is on the floor).
4. Begin vacuuming: Push the vacuum forward and back in slow, overlapping strokes.
5. Use Lift-Away mode: Press the release button to detach the pod for stairs or furniture.

CAUTION! The UV light is for surface sanitization only. Do not look directly at the light.

Specifications

• Model: Shark Navigator UV400 26.
• Type: Upright vacuum with Lift-Away.
• Filtration: Anti-Allergen Complete Seal with HEPA filter.
• Dust Cup Capacity: 1.3 quarts.
• Cord Length: 25 feet.
• Attachments: Crevice tool, dusting brush, upholstery tool, pet multi-tool.
• UV Light: UV-C sanitizing technology.
• Brushroll: Motorized, self-adjusting.
• Power Source: 120V AC, 60Hz.
• Weight: 14.5 lbs.

Controls and Settings

Access controls via buttons and switches on the handle and body.

Handle Controls: POWER button, UV LIGHT button, WAND RELEASE button.

Body Controls: FLOOR SELECTOR switch (Carpet/Hard Floor), LIFT-AWAY RELEASE button, DUST CUP RELEASE button.

Settings: Carpet mode (activates brushroll), Hard Floor mode (reduces brushroll speed), UV Light On/Off, Suction power (single speed).

Using Attachments

Attachments stored on-board for above-floor cleaning.

1. Detach wand: Press the wand release button and pull the wand out.
2. Choose attachment: Select crevice tool, dusting brush, or upholstery tool.
3. Connect: Insert the attachment into the end of the wand until it clicks.
4. Use Lift-Away pod: Detach the pod for handheld cleaning with attachments.
5. Clean: Guide the attachment over surfaces; the vacuum suction will draw in debris.

Tip: For pet hair, use the pet multi-tool attachment on upholstery and stairs.

Cleaning Modes

Supports multiple cleaning configurations for different tasks.

1. Upright Mode: For whole-floor cleaning with motorized brushroll.
2. Lift-Away Mode: Detach the pod for portable cleaning of stairs, furniture, and under low-clearance areas.
3. Above-Floor Mode: Use wand and attachments for ceilings, blinds, and tight spaces.
4. UV Sanitizing Mode: Activate UV light while vacuuming to sanitize surfaces as you clean.

WARNING! Do not use the UV light on humans, animals, or reflective surfaces. Keep the nozzle on the floor when UV is active.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

1. Empty dust cup: Press release button and empty after each use or when full.
2. Clean filters: Rinse HEPA filter and pre-motor filter with cold water every 3 months. Air dry for 24 hours before reinstalling.
3. Clear brushroll: Remove debris wrapped around the brushroll regularly. Unplug vacuum before cleaning.
4. Check for clogs: Inspect hose, wand, and nozzle for blockages if suction decreases.
5. Wipe exterior: Use a dry cloth to clean the vacuum body. Do not use liquids.

CAUTION! Always unplug the vacuum before performing any maintenance. Do not operate with wet filters.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. UV-C light complies with FDA performance standards for ultraviolet radiation emitting products. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug for 10 minutes, then restart.

Service: 1-800-798-7398; www.sharkclean.com