Shark Navigator UV300 Vacuum Cleaner Manual

The Shark Navigator UV300 is an upright vacuum cleaner featuring UV sanitizing technology, powerful suction with Anti-Allergen Complete Seal, a Lift-Away pod for portable cleaning, a large-capacity dust cup, motorized brushroll for carpets and hard floors, advanced swivel steering, HEPA filter, and multiple attachments. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Attachments 7. UV Sanitizing Mode 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Main vacuum body with motorized brushroll, Lift-Away pod, UV sanitizing light, dust cup with HEPA filter, hose, wand, and attachments (crevice tool, dusting brush, upholstery tool).

FeatureDescription
UV Sanitizing TechnologyUses UV-C light to kill germs and bacteria on surfaces
Anti-Allergen Complete SealTraps 99.9% of dust and allergens inside the vacuum
Lift-Away PodDetachable canister for portable above-floor cleaning
Motorized BrushrollAutomatically adjusts between carpets and hard floors
Advanced Swivel SteeringProvides maneuverability around furniture and obstacles
Large Capacity Dust CupEasy-empty, no bags required
HEPA FilterCaptures fine particles and allergens
POWER ButtonTurns vacuum and UV light on/off
Brushroll On/OffDisengages brushroll for delicate floor cleaning
Suction ControlAdjusts suction power for different surfaces

Assembly & Setup

Unpack and inspect all components. Assemble on a flat surface.

  1. Attach handle: Insert handle into top of vacuum body until it clicks into place.
  2. Connect hose: Attach hose to front of vacuum and secure wand to hose end.
  3. Install attachments: Store crevice tool, dusting brush, and upholstery tool on dock.
  4. Install filter: Place HEPA filter in dust cup compartment before first use.
  5. Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Plug in vacuum; follow these steps for initial operation.

  1. Check filter: Ensure HEPA filter is properly installed in dust cup.
  2. Select mode: Choose upright mode for floors or Lift-Away mode for above-floor cleaning.
  3. Adjust settings: Set suction control to MAX for carpets, MIN for hard floors or drapes.
  4. Activate UV: Press UV button to engage sanitizing light (ensure brushroll is engaged).
  5. Begin cleaning: Move vacuum slowly over surfaces for optimal suction and UV exposure.

CAUTION! Do not look directly at UV light. Keep vacuum away from water and wet surfaces.

Specifications

Controls and Settings

Main controls located on handle and body. Handle: POWER button, Suction Control slider, Brushroll On/Off switch. Body: UV Mode button, Lift-Away release, Dust Cup release.

Settings: Suction Control (MAX for carpets, MIN for delicate surfaces). Brushroll (On for carpets, Off for hard floors/drapes). UV Mode (On for sanitizing, automatically turns off when vacuum is lifted).

Indicator Lights: Power (green), UV Active (blue), Brushroll Jam (red), Full Dust Cup (yellow).

Using Attachments

For above-floor cleaning, detach Lift-Away pod and connect desired attachment.

  1. Detach pod: Press Lift-Away release button and lift pod from vacuum base.
  2. Select attachment: Choose crevice tool for tight spaces, dusting brush for surfaces, upholstery tool for furniture.
  3. Connect: Insert attachment into end of wand or hose.
  4. Clean: Use suction control to adjust power as needed.
  5. Return: Reattach pod to base until it clicks.

Tip: Turn off brushroll when using attachments on delicate surfaces.

UV Sanitizing Mode

UV-C light kills up to 99.9% of germs and bacteria on surfaces.

  1. Activate: Press UV button while vacuum is on and brushroll is engaged.
  2. Operation: Blue light indicates UV is active. Light turns off when vacuum is lifted or turned off.
  3. Effectiveness: Move slowly (approx. 1 ft/sec) over surfaces for proper exposure.
  4. Safety: Do not stare at UV light. Keep away from skin and eyes.
  5. Deactivate: Press UV button again or turn off vacuum.

WARNING! UV light is for surface sanitization only. Not a substitute for chemical disinfectants.

Maintenance & Cleaning

Regular maintenance ensures optimal performance. Unplug before servicing.

  1. Empty dust cup: Press release button, remove cup, and empty contents into trash.
  2. Clean filter: Remove HEPA filter every month and tap to remove dust. Wash with cold water every 3 months; air dry 24 hours.
  3. Clear brushroll: Turn off vacuum, remove debris from brushroll with scissors or tool.
  4. Check hose/wand: Remove clogs with long object.
  5. Wipe exterior: Use dry cloth; no liquids.

CAUTION! Do not operate without filter. Ensure all parts are completely dry before reassembly.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. UV-C technology complies with FDA and IEC standards. For support, visit sharkclean.com or contact 1-800-798-7398.

Troubleshooting

SymptomPossible CauseCorrective Action
Vacuum won't turn onPower cord/outletCheck power cord connection; try different outlet; ensure POWER button is pressed.
Loss of suctionFull dust cup/clogEmpty dust cup; check hose, wand, and brushroll for clogs; clean filter.
Brushroll not spinningJam/obstructionTurn off vacuum, remove debris from brushroll; ensure Brushroll switch is ON.
UV light not workingMode/engagementEnsure vacuum is on flat surface with brushroll engaged; press UV button again.
Vacuum overheatingClog/filterTurn off and unplug; check for clogs; clean filter; allow to cool for 60 minutes.
Strange noisesForeign objectTurn off immediately; check for objects in brushroll, hose, or wand.

Reset: Unplug for 10 minutes, then restart.

Service: 1-800-798-7398; sharkclean.com

Shark Navigator UV300 Vacuum Cleaner Manual © - All Rights Reserved 2025