Shark Navigator NV36A 26 Vacuum Cleaner Manual

The Shark Navigator NV36A 26 is a versatile upright vacuum cleaner featuring Lift-Away technology, Anti-Allergen Complete Seal technology with a HEPA filter, a motorized brushroll for carpets and hard floors, a large-capacity dust cup, a 25-foot power cord, multiple cleaning modes (upright, Lift-Away, handheld), a crevice tool, dusting brush, and upholstery tool. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes & Attachments 7. Maintenance & Care 8. Filter System 9. Storage & Handling 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Upright vacuum body, Lift-Away pod, motorized floor nozzle, wand, dust cup with HEPA filter, hose, and accessory tools.

Feature	Description
Lift-Away Technology	Detach the pod for portable, above-floor cleaning
Anti-Allergen Complete Seal	Sealed system with HEPA filter traps 99.9% of dust and allergens
Motorized Brushroll	Automatically adjusts between carpets and hard floors
Large Dust Cup	Easy-to-empty, no bags required
25-Foot Power Cord	Extended reach for large areas
Cleaning Modes	Upright, Lift-Away, and handheld configurations
Accessory Tools	Crevice tool, dusting brush, upholstery tool included
ON/OFF Switch	Powers the vacuum on and off
Brushroll On/Off	Switch to turn brushroll on for carpets or off for hard floors
Floor Selector	Adjusts suction for carpet or hard floor settings

Assembly & Setup

Unpack and inspect all contents. Assemble according to instructions.

Attach the wand: Insert the wand into the upright body until it clicks into place.
Connect the hose: Attach the hose to the designated port on the pod.
Install the floor nozzle: Slide the nozzle onto the base until it locks.
Attach accessories: Store tools on the accessory caddy or wand.
Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, ensure all filters are installed correctly.

Check filters: Ensure the HEPA filter and pre-motor filter are properly seated.
Select cleaning mode: Choose upright for floors or detach the pod for Lift-Away mode.
Adjust settings: Set floor selector to match your surface (carpet or hard floor).
Turn on: Press the power switch and begin cleaning.

CAUTION! Do not use on wet surfaces. Keep hair, loose clothing, and fingers away from moving parts.

Specifications

Model: Shark Navigator NV36A 26.
Technology: Lift-Away, Anti-Allergen Complete Seal with HEPA filter.
Power Cord: 25 feet.
Dust Cup Capacity: 1.2 dry quarts.
Cleaning Modes: Upright, Lift-Away, handheld.
Attachments:Crevice tool, dusting brush, upholstery tool.
Power Source: 120V AC, 60Hz.
Weight: Approximately 14.5 lbs.

Controls and Settings

Main controls located on the vacuum body.

Upright Body: ON/OFF switch, Brushroll On/Off switch, Floor Selector (Carpet/Hard Floor), Lift-Away release button.

Settings: Carpet mode (brushroll on, high suction), Hard Floor mode (brushroll off or on, adjusted suction). Lift-Away mode: Detach pod for portable cleaning. Handheld mode: Use with hose and tools for detailed cleaning.

Cleaning Modes & Attachments

Use different modes and tools for various cleaning tasks.

Upright Mode: For large carpeted and hard floor areas.
Lift-Away Mode: Detach pod to clean stairs, under furniture, and above floors.
Handheld Mode: Use hose and tools for upholstery, crevices, and dusting.
Attachments: Crevice tool for tight spaces, dusting brush for surfaces, upholstery tool for furniture.

Tip: Turn off the brushroll when cleaning hard floors or area rugs to prevent scattering debris.

Playing DVD Media

This section is not applicable to a vacuum cleaner. Please refer to the relevant sections for operation and maintenance.

Accessibility Features

This section is not applicable to a vacuum cleaner. Please refer to the controls and cleaning modes for ease of use.

Care & Cleaning

Regular maintenance ensures optimal performance.

Empty dust cup: Press release button and empty when full or after each use.
Clean filters: Rinse HEPA filter and pre-motor filter with cold water every 3 months (allow to dry 24 hours).
Clear brushroll: Remove debris wrapped around the brushroll regularly.
Check for clogs: Inspect hose, wand, and nozzle if suction is reduced.

CAUTION! Unplug vacuum before maintenance. Do not use damaged filters. Ensure all parts are completely dry before reassembly.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power source/switch	Check outlet; ensure power cord is plugged in; press ON/OFF switch firmly.
Loss of suction	Full dust cup/clogged filter	Empty dust cup; check and clean filters; remove clogs from hose or nozzle.
Brushroll not spinning	Debris/switch setting	Clear debris from brushroll; ensure Brushroll switch is ON for carpet mode.
Vacuum is overheating	Clog/full dust cup	Turn off and unplug; let cool; check for and clear clogs; empty dust cup.
Unusual noise	Obstruction in airpath	Turn off and unplug; inspect hose, wand, and nozzle for blockages.

Reset: Unplug vacuum, clear all blockages, empty dust cup, and clean filters.

Service: 1-800-798-7398; sharkclean.com