Shark Navigator NV27PR Vacuum Cleaner Manual

The Shark Navigator NV27PR is a lightweight, upright vacuum cleaner featuring Lift-Away technology, Anti-Allergen Complete Seal, HEPA filter, motorized brush roll for carpets, swivel steering, crevice tool, dusting brush, upholstery tool, and a large-capacity dust cup. It is designed for deep cleaning on both carpets and hard floors. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Upright vacuum body, Lift-Away pod, motorized brush roll, HEPA filter, dust cup, hose, wand, and accessory tools.

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

1. Attach wand: Insert wand into hose until it clicks securely.
2. Connect hose: Attach hose to vacuum body at the designated port.
3. Install accessories: Store tools on onboard caddy or attach as needed.
4. Check filters: Ensure HEPA and pre-motor filters are properly seated.

WARNING! Ensure vacuum is unplugged during assembly. Keep fingers away from brush roll.

First-Time Use

Plug into a standard 120V outlet; turn on power switch.

1. Select mode: Use as upright for floors or detach pod for above-floor cleaning.
2. Adjust height: For carpets, set brush roll height appropriately (if adjustable).
3. Begin vacuuming: Push vacuum forward and back in overlapping strokes.
4. Empty dust cup: Press release button to remove and empty when full.

CAUTION! Do not vacuum wet spills, large objects, or hot ashes.

Specifications

• Model: Shark Navigator NV27PR.
• Technology: Lift-Away, Anti-Allergen Complete Seal.
• Filtration: HEPA filter, foam and felt pre-motor filters.
• Brush Roll: Motorized, on/off control for hard floors.
• Cord Length: 25 feet.
• Dust Cup Capacity: 1.5 dry quarts.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Power Source: 120V AC, 60Hz.
• Weight: Approximately 12 lbs.

Controls and Settings

Main controls: Power switch, brush roll on/off, height adjustment (if applicable), Lift-Away release button.

Upright Mode: For floor cleaning. Lift-Away Mode: Detach pod for stairs, furniture, and above-floor areas.

Brush Roll Control: Turn off for hard floors to prevent scattering debris. Height Adjustment: Set to appropriate carpet height for optimal cleaning. Dust Cup Release: Button to remove and empty dust cup. Hose and Wand: Extend for reach; detach for tool use.

Using Attachments

Attach tools to wand or hose end for specialized cleaning.

1. Detach pod: Press Lift-Away release button to separate pod from vacuum body.
2. Connect tool: Insert desired tool into end of wand or hose.
3. Clean: Use crevice tool for edges; dusting brush for shelves; upholstery tool for furniture.
4. Return to upright: Reattach pod by aligning and pressing until it clicks.

Tip: Store tools on onboard caddy for easy access.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Empty dust cup: After each use or when full; press release button.
2. Clean brush roll: Remove debris wrapped around roll; check for blockages.
3. Inspect hose and wand: Clear any clogs using a long object.
4. Check filters: Clean or replace as recommended.

WARNING! Unplug vacuum before performing any maintenance.

Filter Care

Filters trap dust and allergens; maintain regularly.

HEPA Filter: Rinse under cold water every 3 months; air dry for 24 hours before reinstalling. Pre-Motor Filters: Foam and felt filters; rinse monthly, air dry completely. Never operate vacuum without all filters installed.

Storage & Care

Store in a cool, dry place. Wrap cord around cord hooks.

CAUTION! Do not store vacuum with wet filters. Keep away from heat sources.

Regulatory Information

This vacuum cleaner complies with relevant safety standards. Copyright © SharkNinja Operating LLC. For support, visit sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug for 60 minutes if motor overheats.

Service: 1-800-798-7398; sharkclean.com