Shark Navigator NV22LB Vacuum Cleaner Manual

The Shark Navigator NV22LB is an upright vacuum cleaner featuring Lift-Away technology, Anti-Allergen Complete Seal with HEPA filter, swivel steering, brushroll shutoff, crevice tool, dusting brush, upholstery tool, and a 25-foot power cord. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Lift-Away pod, swivel steering handle, dust cup, HEPA filter, brushroll, crevice tool, dusting brush, upholstery tool.

Assembly Instructions

Unpack and inspect all parts. Assemble on a flat surface.

1. Attach handle: Insert handle into body until it clicks into place.
2. Install wand: Insert wand into handle until secure.
3. Attach hose: Connect hose to pod and wand connections.
4. Install filters: Place HEPA filter in back; foam filter in front.
5. Attach tools: Store crevice tool, dusting brush, and upholstery tool on caddy.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching.

First-Time Setup

Plug in vacuum; perform initial check.

1. Check filters: Ensure both filters are properly seated.
2. Test suction: Turn on vacuum; verify strong suction.
3. Test brushroll: Engage brushroll on carpet; ensure rotation.
4. Test attachments: Connect each tool to ensure proper fit.
5. Test Lift-Away: Press release button; lift pod away from base.

CAUTION! Keep hair, loose clothing, and fingers away from brushroll.

Specifications

• Model: Shark Navigator NV22LB.
• Technology: Lift-Away with Anti-Allergen Complete Seal.
• Filtration: HEPA filter captures 99.9% of dust and allergens.
• Cord Length: 25 feet.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Brushroll: Motorized with shutoff for hard floors.
• Dust Cup Capacity: 1.2 dry quarts.
• Power Source: 120V AC, 60Hz.
• Weight: 12.5 lbs.

Controls and Settings

Access controls via handle and body. Handle: Power switch, brushroll shutoff button. Body: Lift-Away release, wand release pedal, dust cup release.

Power Switch: On/Off toggle. Brushroll Shutoff: Turns off brushroll for hard floors. Lift-Away Release: Detaches pod from base. Wand Release Pedal: Releases wand for above-floor cleaning. Dust Cup Release: Opens bottom to empty dust cup.

Using Attachments

Attach tools to wand or hose for above-floor cleaning.

1. Detach wand: Press wand release pedal; pull wand out.
2. Connect tool: Insert crevice tool, dusting brush, or upholstery tool into wand.
3. Use hose: For hard-to-reach areas, connect tool directly to hose.
4. Clean: Move tool over surface; vacuum will suction debris.
5. Store: Return tools to caddy after use.

Tip: Use brushroll shutoff when using attachments on hard floors.

Cleaning Modes

Supports upright and Lift-Away modes.

1. Upright mode: Use for carpets and large floor areas.
2. Lift-Away mode: Press release button; lift pod to clean above floors.
3. Above-floor cleaning: Use wand and attachments for stairs, furniture.
4. Hard floor cleaning: Engage brushroll shutoff to prevent scattering debris.
5. Edge cleaning: Use side of vacuum head to clean along baseboards.

WARNING! Do not vacuum wet surfaces, liquids, or sharp objects.

Maintenance & Care

Regular maintenance ensures optimal performance.

1. Empty dust cup: Press release; empty into trash when full.
2. Clean filters: Rinse HEPA and foam filters monthly; air dry 24 hours.
3. Clear brushroll: Remove hair and debris from brushroll regularly.
4. Check hose: Remove clogs if suction decreases.
5. Inspect cord: Check for damage; replace if frayed.

CAUTION! Unplug vacuum before maintenance. Do not use without filters.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug for 60 minutes; plug back in.

Service: 1-800-798-7398; www.sharkclean.com