Shark Navigator Lift-Away UV730 Series Vacuum Cleaner Manual

The Shark Navigator Lift-Away UV730 Series is a versatile upright vacuum cleaner featuring Lift-Away technology for portable cleaning, Anti-Allergen Complete Seal technology with a HEPA filter, powered floor nozzle for carpets and hard floors, LED headlights, a large-capacity dust cup, and multiple attachments for above-floor cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main vacuum body with motor, Lift-Away pod, Powered floor nozzle with brushroll, Dust cup with HEPA filter, Hose with wand, Cleaning attachments (crevice tool, dusting brush, upholstery tool).

Assembly & Setup

Unpack all parts and inspect contents. Assemble on a flat, stable surface.

1. Attach the wand: Insert the wand into the hose port on the vacuum body until it clicks.
2. Connect the hose: Attach the hose end to the wand connector.
3. Install floor nozzle: Align the floor nozzle with the vacuum body and push until it locks.
4. Attach cleaning tools: Store tools on the accessory caddy or attach directly to the wand.
5. Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, ensure all parts are properly assembled and filters are installed.

1. Check filters: Ensure HEPA filter and pre-motor filter are correctly seated.
2. Select floor setting: Use the dial on the floor nozzle for carpets (setting I) or hard floors (setting II).
3. Power on: Press the ON/OFF switch; the LED headlights will illuminate.
4. Begin vacuuming: Push vacuum forward and back slowly for effective cleaning.
5. Empty dust cup: Press release button to remove and empty when full.

CAUTION! Do not vacuum large objects, liquids, or hot ashes. Keep hair and loose clothing away from brushroll.

Specifications

• Model: Shark Navigator Lift-Away UV730 Series.
• Technology: Lift-Away, Anti-Allergen Complete Seal with HEPA filter.
• Floor Nozzle: Powered brushroll with LED headlights, multi-surface settings.
• Dust Cup Capacity: 1.5 dry quarts.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Cord Length: 25 feet.
• Power Source: 120V AC, 60Hz.
• Weight: 14.5 lbs (assembled).
• Warranty: 5-year limited warranty.

Controls and Settings

Main controls located on the vacuum body and floor nozzle.

Vacuum Body: ON/OFF switch, Lift-Away release button, Hose release latch. Floor Nozzle: Brushroll ON/OFF switch, Carpet/Hard Floor dial, Height adjustment (if applicable).

Operation: Turn ON/OFF switch to power vacuum. Use Brushroll switch to engage/disengage motorized cleaning. Adjust floor dial for surface type. Press Lift-Away button to detach pod for above-floor cleaning. Use hose and wand with attachments for furniture, stairs, and tight spaces.

Using Attachments

For above-floor cleaning, detach the wand and attach desired tool.

1. Detach wand: Press the release button on the vacuum body and pull wand out.
2. Select tool: Attach crevice tool, dusting brush, or upholstery tool to the wand end.
3. Clean: Use tool on stairs, furniture, blinds, corners, and other surfaces.
4. Return to upright: Reinsert wand into vacuum body until it clicks.

Tip: Store attachments on the accessory caddy for easy access.

Lift-Away Mode

Lift-Away mode allows portable cleaning without the floor nozzle.

1. Detach pod: Press the Lift-Away release button and lift the pod away from the floor nozzle.
2. Attach hose: The hose remains connected to the pod; extend the wand if needed.
3. Select attachment: Choose appropriate tool for the cleaning task.
4. Clean: Carry the lightweight pod to clean stairs, furniture, ceilings, and other areas.
5. Reattach: Place pod back onto floor nozzle until it clicks into place.

WARNING! Ensure the pod is securely attached before using in upright mode. Do not use Lift-Away mode on stairs without proper footing.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Empty dust cup: Press release button, remove cup, and empty contents into trash. Clean cup with dry cloth.
2. Clean filters: Remove HEPA filter and pre-motor filter every month. Tap gently to remove dust; rinse with cold water if needed (air dry completely for 24 hours before reinstalling).
3. Clear brushroll: Turn off and unplug vacuum. Remove floor nozzle and clear any hair or debris wrapped around the brushroll.
4. Check hose and attachments: Remove any clogs with a long, flexible object.

CAUTION! Always unplug vacuum before maintenance. Do not use damaged filters or parts.

Regulatory Information

This vacuum cleaner complies with FCC Part 15 for Class B digital devices. Copyright © SharkNinja Operating LLC. All trademarks are property of SharkNinja. For support, visit www.sharkclean.com or contact 1-800-798-7398. Keep these instructions for future reference.

Troubleshooting

Reset: Unplug vacuum for 60 minutes if overheating occurs.

Service: 1-800-798-7398; www.sharkclean.com