Shark NAVIGATOR LIFT-AWAY PRO NV356Q 26 Vacuum Cleaner Manual

The Shark NAVIGATOR LIFT-AWAY PRO NV356Q 26 is a versatile upright vacuum cleaner featuring Lift-Away technology, Anti-Allergen Complete Seal Technology, a HEPA filter, a motorized brushroll for carpets, a wide upholstery tool, a dusting brush, a crevice tool, and a 26-foot power cord. It is designed for deep cleaning carpets, bare floors, and above-floor areas. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Cleaning Tools 7. Emptying the Dust Cup 8. Filter Maintenance 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main vacuum body with motor, Lift-Away pod, floor nozzle with motorized brushroll, wand, hose, and accessory tools.

Feature	Description
Lift-Away Technology	Detachable pod for portable above-floor cleaning
Anti-Allergen Complete Seal	Sealed system with HEPA filter to trap dust and allergens
Motorized Brushroll	Deep cleans carpets and agitates embedded dirt
Brushroll Shutoff	Switch to turn off brushroll for bare floors
Wide Upholstery Tool	For cleaning furniture, stairs, and auto interiors
Dusting Brush	For delicate surfaces like blinds and lampshades
Crevice Tool	For tight spaces like corners and between cushions
26-Foot Power Cord	Extended reach for cleaning large areas
Large Capacity Dust Cup	Easy-to-empty, bagless design
On-Board Tool Storage	Convenient storage for accessories

Assembly & Setup

Unpack all parts and inspect for damage. Assemble on a flat surface.

Attach the wand: Insert the wand into the socket on the vacuum body until it clicks.
Attach the hose: Connect the hose end to the port on the vacuum body.
Attach the floor nozzle: Slide the nozzle onto the wand until it locks into place.
Install filters: Ensure both the pre-motor and HEPA filters are correctly seated.
Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, perform a quick test to ensure all components are working.

Power on: Press the foot pedal or switch to turn on the vacuum.
Select floor type: For carpets, ensure brushroll is on. For bare floors, turn brushroll off.
Adjust height: Use the dial on the floor nozzle to match carpet pile (if applicable).
Test suction: Place hand over hose end to confirm strong suction.
Test Lift-Away: Press the release button to detach the pod for above-floor cleaning.

CAUTION! Keep hair, loose clothing, and fingers away from brushroll and openings.

Specifications

Model: NAVIGATOR LIFT-AWAY PRO NV356Q 26.
Type: Upright vacuum with Lift-Away pod.
Technology: Anti-Allergen Complete Seal with HEPA filter.
Cord Length: 26 feet.
Dust Cup Capacity: [Specify volume, e.g., 1.5 quarts].
Filters: Pre-motor foam filter, post-motor HEPA filter.
Attachments: Motorized floor nozzle, wide upholstery tool, dusting brush, crevice tool.
Power Source: 120V AC, 60Hz.
Weight: Approximately [e.g., 15 lbs].

Controls and Settings

Main controls located on the vacuum body and floor nozzle.

On Vacuum Body: Power switch/foot pedal, Hose release button, Cord rewind button (if equipped). On Floor Nozzle: Brushroll on/off switch, Carpet height adjustment dial.

Settings: Power (On/Off), Brushroll (On for carpets/Off for bare floors), Suction control (if available), Height adjustment (multiple settings for different carpets).

Using Cleaning Tools

For above-floor cleaning, detach the Lift-Away pod and attach desired tool.

Detach pod: Press the release button and lift the pod away from the floor nozzle.
Attach tool: Click the desired tool (upholstery, brush, crevice) onto the hose end.
Clean: Use the tool on furniture, stairs, blinds, or tight spaces.
Reattach: Return the pod to the docking station on the floor nozzle until it clicks.

Tip: For best results on upholstery, use slow, overlapping strokes.

Emptying the Dust Cup

Empty the dust cup when it reaches the MAX fill line.

Turn off and unplug the vacuum.
Press the dust cup release button and lift the cup away.
Hold over a trash can and press the bottom release latch to open the door.
Tap gently to remove debris. Close the door securely.
Reattach the dust cup until it clicks into place.

WARNING! Always unplug before emptying. Do not overfill.

Filter Maintenance

Regular filter cleaning ensures optimal performance and suction.

Pre-motor Foam Filter: Rinse with cold water every month. Air dry completely for 24 hours before reinstalling. HEPA Filter: Tap gently to remove dust every 3 months. Replace every 12-18 months or as needed.

CAUTION! Never operate the vacuum without all filters installed and completely dry.

Care & Storage

Unplug and clean exterior with a dry cloth. Store in a cool, dry place.

Check brushroll for tangled hair or threads monthly and cut away debris with scissors. Wind power cord neatly around cord hooks.

CAUTION! Do not use wet cloths or cleaners on electrical parts. Store indoors.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup, clogged hose/filter	Empty dust cup; check hose and filters for blockages; clean filters.
Brushroll not spinning	Tangled debris, belt issue, switch off	Unplug, remove debris from brushroll; check belt; ensure brushroll is set to ON.
Vacuum won't turn on	No power, faulty outlet, cord damage	Check outlet; try another outlet; inspect power cord for damage.
Lift-Away pod not detaching	Release button not fully pressed	Press release button firmly and lift straight up.
Unusual noise/vibration	Foreign object in hose or brushroll	Unplug, inspect hose, nozzle, and brushroll for obstructions.

Reset: Unplug for 60 seconds, then plug back in.

Service: 1-800-798-7398; sharkclean.com