Shark Navigator Lift-Away ADV Vacuum Cleaner Manual

The Shark Navigator Lift-Away ADV is a versatile upright vacuum cleaner featuring Lift-Away technology for portable above-floor cleaning, Anti-Allergen Complete Seal Technology with a HEPA filter, a motorized brushroll for carpets, a crevice tool, dusting brush, upholstery tool, and a wide upholstery tool. It includes a large-capacity dust cup, multiple suction settings, swivel steering for maneuverability, and a wand for extended reach. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes 7. Maintenance & Care 8. Accessory Guide 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Main vacuum body with motor, Lift-Away pod, motorized floor nozzle, wand, dust cup with HEPA filter, and accessory set.

FeatureDescription
Lift-Away TechnologyDetachable pod for portable cleaning of stairs, furniture, and above-floor areas
Anti-Allergen Complete SealHEPA filter captures 99.9% of dust and allergens, trapping them inside the vacuum
Motorized BrushrollDeep cleans carpets and agitates embedded dirt
Swivel SteeringProvides full maneuverability around furniture and obstacles
Large Dust CupEasy-to-empty, bagless dust cup with large capacity
Suction ControlAdjustable settings for different floor types (carpet/hard floor)
Accessory StorageOn-board storage for crevice tool, dusting brush, and upholstery tool
Wand ReleaseQuick-release button for extending the wand
Power SwitchTurns vacuum on/off
Brushroll On/OffSwitch to disable brushroll for hard floor cleaning

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

  1. Attach the handle: Insert the handle into the top of the main body until it clicks into place.
  2. Connect the wand: Insert the wand into the socket on the front of the vacuum until it locks.
  3. Attach the floor nozzle: Align the nozzle with the wand connector and push until it clicks.
  4. Install accessories: Store the crevice tool, dusting brush, and upholstery tool in the on-board caddy.
  5. Plug into a standard 120V AC outlet.

WARNING! Ensure the vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before cleaning, perform a quick check and setup.

  1. Check filter: Ensure the HEPA filter is properly seated in the dust cup lid.
  2. Empty dust cup: Confirm the dust cup is empty before starting.
  3. Select floor setting: Use the suction control dial on the handle for carpet or hard floor.
  4. Power on: Press the power switch on the handle.
  5. Test Lift-Away: Press the release button to detach the pod for above-floor cleaning.

CAUTION! Do not use on wet surfaces. Keep hair, loose clothing, and fingers away from brushroll.

Specifications

Controls and Settings

Main controls located on the handle and body. Handle: Power switch, suction control dial, brushroll on/off switch. Body: Lift-Away release button, wand release button, dust cup release latch.

Settings: Suction control (CARPET/HARD FLOOR), Brushroll on/off (for hard floors or delicate rugs). Lift-Away mode: Detach pod for portable cleaning. Accessory mode: Attach tools to wand or hose for above-floor cleaning.

Cleaning Modes

Three primary cleaning modes: Upright, Lift-Away, and Handheld.

  1. Upright Mode: For carpets and large floor areas. Use suction control for carpet type.
  2. Lift-Away Mode: Press release button to detach pod; clean stairs, furniture, under furniture.
  3. Handheld Mode: Remove wand and attach tool directly to hose for spot cleaning.

Tip: For best results on carpets, use high suction with brushroll on. For hard floors, use low suction with brushroll off.

Maintenance & Care

Regular maintenance ensures optimal performance.

  1. Empty dust cup: Press release latch; empty when full or after each use.
  2. Clean filters: Rinse foam and felt filters monthly; air dry completely for 24 hours before reinstalling.
  3. Check brushroll: Regularly remove hair and debris wrapped around brushroll.
  4. Inspect hose and wand: Clear any blockages with a long, flexible object.
  5. Store properly: Wind cord around cord hooks; store in a dry place.

WARNING! Always unplug vacuum before maintenance. Do not use damaged filters or brushroll.

Accessory Guide

Each accessory is designed for specific cleaning tasks.

AccessoryUse
Crevice ToolCleans tight spaces, corners, between cushions
Dusting BrushGentle cleaning of shelves, blinds, lampshades
Upholstery ToolCleans sofas, chairs, car interiors
Wide Upholstery ToolLarger surface area for faster fabric cleaning

Attach accessories to the wand or directly to the hose in Lift-Away mode.

Regulatory Information

This vacuum cleaner complies with FCC Part 15 Subpart B for Class B digital devices. Copyright © SharkNinja Operating LLC. All trademarks are property of SharkNinja. For support, visit sharkclean.com or contact 1-800-798-7398.

Troubleshooting

SymptomPossible CauseCorrective Action
Loss of suctionFull dust cup, clogged filter or hoseEmpty dust cup; check and clean filters; clear hose/wand blockages.
Brushroll not spinningObstruction, belt issue, switch offClear debris from brushroll; check belt; ensure brushroll switch is ON.
Vacuum won't turn onPower cord, outlet, switchCheck power cord connection; test outlet; ensure power switch is pressed.
Lift-Away pod not detachingRelease button stuck, misalignedPress release button firmly; ensure pod is properly seated before detaching.
OverheatingClogged filter, full dust cupUnplug vacuum; let cool; empty dust cup and clean filters.

Reset: Unplug vacuum for 60 minutes if overheating occurs.

Service: 1-800-798-7398; sharkclean.com

Shark Navigator Lift-Away ADV Vacuum Cleaner Manual © - All Rights Reserved 2025