Shark Lift-Away ZU700 Series Vacuum Cleaner Manual

The Shark Lift-Away ZU700 Series is a versatile upright vacuum cleaner featuring Lift-Away technology for portable deep cleaning, DuoClean PowerFins brushroll for carpets and hard floors, Anti-Allergen Complete Seal technology with HEPA filter, LED headlights, and a variety of attachments. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Lift-Away Mode 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Main vacuum body with motor, Lift-Away pod, DuoClean PowerFins brushroll, Dust Cup, HEPA Filter, Hose, Wand, and various attachments.

Feature	Description
Lift-Away Technology	Detachable pod for portable cleaning above floors
DuoClean PowerFins Brushroll	Combines bristle brush and soft roller for carpets and hard floors
Anti-Allergen Complete Seal	Sealed system with HEPA filter traps 99.9% of dust and allergens
LED Headlights	Illuminates hidden debris under furniture
Power Switch	Turns vacuum on/off
Brushroll On/Off	Disengages brushroll for delicate floor cleaning
Suction Control	Adjusts suction power for different surfaces
Dust Cup Release	Button to empty dust cup
Lift-Away Release Button	Detaches the pod from the main body
Wand Release Pedal	Releases telescoping wand for extended reach

Assembly & Setup

Unpack and inspect all contents. Assemble on a flat, stable surface.

Attach the handle: Align handle with top of vacuum body and push until it clicks into place.
Insert the wand: Slide the wand into the hose until it locks.
Attach the floor nozzle: Connect the DuoClean nozzle to the wand or directly to the hose.
Install attachments: Store crevice tool, dusting brush, and upholstery tool on the accessory caddy.
Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, ensure all parts are properly assembled and filters are installed.

Check filters: Ensure HEPA filter and pre-motor filter are correctly seated.
Select surface setting: Use suction control dial for appropriate surface (Low for hard floors, High for carpets).
Turn on: Press power switch; LED lights will illuminate.
Adjust height: For carpets, ensure nozzle is at correct height setting for optimal cleaning.
Empty dust cup: After initial use, empty dust cup to ensure maximum suction.

CAUTION! Do not vacuum large objects, liquids, or hot ashes. Keep hair and loose clothing away from brushroll.

Specifications

Model Series: ZU700 (ZU701, ZU702, etc.)
Technology: Lift-Away, DuoClean PowerFins, Anti-Allergen Complete Seal.
Filtration: HEPA filter, pre-motor foam filter.
Attachments: Crevice tool, dusting brush, upholstery tool, pet multi-tool.
Power Cord Length: 25 feet.
Dust Cup Capacity: 1.1 quarts.
Power Source: 120V AC, 60Hz.
Weight: Approximately 14 lbs.

Controls and Settings

Main controls located on handle and body. Handle: Power switch, suction control dial. Body: Brushroll on/off switch, dust cup release, Lift-Away release button.

Settings: Suction Control (Low/High), Brushroll On/Off (for hard floors or area rugs), Height Adjustment (for carpets).

LED Indicators: Headlights activate when vacuum is on. Filter Check Light: Illuminates when filters need cleaning or replacement.

Using Attachments

For above-floor cleaning, detach hose and wand, then connect desired attachment.

Turn off vacuum and unplug from outlet.
Press wand release pedal to remove wand from floor nozzle.
Connect attachment (crevice tool, dusting brush, etc.) to end of wand or hose.
Plug in vacuum, turn on, and clean surfaces.
Store attachments on caddy when not in use.

Tip: Use upholstery tool for sofas and curtains; use crevice tool for tight spaces.

Lift-Away Mode

Enables portable cleaning of stairs, furniture, and above-floor areas.

Ensure vacuum is turned off.
Press Lift-Away release button on back of vacuum.
Lift the pod away from the floor nozzle and main body.
Carry the pod by its handle; hose remains connected.
Use attachments as needed for detailed cleaning.
To reattach, align pod with main body and push down until it clicks.

WARNING! Do not carry vacuum by hose. Ensure pod is securely attached before resuming upright cleaning.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

Empty dust cup: Press release button; empty contents into trash.
Clean filters: Rinse HEPA filter and foam filter with cold water every month; air dry completely for 24 hours before reinstalling.
Clear brushroll: Remove debris and hair from brushroll regularly; press tabs to remove brushroll for thorough cleaning.
Check for clogs: Inspect hose, wand, and nozzle for blockages if suction decreases.
Wipe exterior: Use dry cloth to clean vacuum body.

CAUTION! Never use vacuum without filters. Ensure all parts are completely dry before reassembly.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. All trademarks are property of SharkNinja. For support, visit sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power source/switch	Check outlet; ensure power switch is pressed; check cord for damage.
Loss of suction	Full dust cup/clogged filters	Empty dust cup; clean filters; check hose and nozzle for clogs.
Brushroll not spinning	Obstruction/switch setting	Clear debris from brushroll; ensure brushroll is turned on.
Vacuum overheating	Clogged filters/blockage	Turn off and unplug; clean filters; clear any blockages; allow to cool.
Lift-Away pod not detaching	Release button not fully pressed	Press release button firmly while lifting pod.

Reset: Unplug vacuum for 30 minutes if motor overheats.

Service: 1-800-798-7398; sharkclean.com