Shark Lift-Around NP318 40 Vacuum Cleaner Manual

The Shark Lift-Around NP318 40 is a versatile corded stick vacuum cleaner with Lift-Away technology, allowing it to detach from the floor nozzle for portable above-floor cleaning. It features a HEPA filter, motorized brush roll for carpets, multiple cleaning modes, a large dust cup, crevice tool, and upholstery tool. Powered by a 120V AC motor. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Cleaning Modes & Attachments 7. Emptying & Cleaning the Dust Cup 8. Filter Maintenance 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main vacuum body with motor, Lift-Away pod, floor nozzle with motorized brush, dust cup, HEPA filter, crevice tool, upholstery tool, power cord.

Feature	Description
Lift-Away Technology	Detaches vacuum pod for portable cleaning above floors
Motorized Brush Roll	Activates for deep carpet cleaning; can be turned off for hard floors
HEPA Filter	Captures 99.9% of dust and allergens
Large Dust Cup	Easy-empty, 0.9 dry quarts capacity
Crevice Tool	For tight spaces, corners, and edges
Upholstery Tool	For furniture, stairs, and car interiors
Power Cord	25-foot length for extended reach
Cleaning Modes	Floor, Above-Floors, Handheld
On/Off Switch	Controls power and brush roll
Wand Release	Adjusts height and detaches wand

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

Attach wand to floor nozzle: Insert wand end into nozzle until it clicks.
Connect vacuum body: Align vacuum body with wand and push down until secure.
Install filter: Ensure HEPA filter is correctly seated in filter compartment.
Attach hose: Connect hose to vacuum body port if detached.
Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Check all connections are secure.

First-Time Use

Plug in vacuum; select appropriate cleaning mode.

Floor cleaning: Ensure vacuum is in floor mode with brush roll ON for carpets.
Above-floor cleaning: Press Lift-Away release button to detach pod; use hose and tools.
Empty dust cup: Press release button to remove and empty cup when full.
Check filter: Ensure HEPA filter is clean before use.

CAUTION! Do not vacuum wet spills, large objects, or hot ashes. Keep hair and loose clothing away from brush roll.

Specifications

Model: NP318 40.
Type: Corded stick vacuum with Lift-Away.
Dust Cup Capacity: 0.9 dry quarts.
Filter: HEPA filter, washable.
Cord Length: 25 feet.
Cleaning Modes: Floor, Above-Floor, Handheld.
Attachments: Crevice tool, upholstery tool.
Power Source: 120V AC, 60Hz.
Weight: 12.5 lbs (assembled).

Controls and Settings

Main controls located on vacuum body. Floor Nozzle: Brush roll ON/OFF switch. Vacuum Body: Power button, Lift-Away release button, dust cup release.

Operation: Plug in, press power button. For carpets, ensure brush roll is ON. For hard floors, turn brush roll OFF to prevent scattering debris. Use Lift-Away release to detach pod for above-floor cleaning.

Settings: Brush roll control (On/Off), suction power (single speed), height adjustment (via wand release).

Cleaning Modes & Attachments

Three primary modes: Floor, Above-Floor (Lift-Away), Handheld.

Floor Mode: Attach floor nozzle; use for carpets and hard floors.
Above-Floor Mode: Detach pod; connect hose and desired tool (crevice or upholstery).
Handheld Mode: Remove pod from wand; use as portable vacuum with tools.

Tip: Turn off brush roll when cleaning hard floors or area rugs to avoid damage.

Emptying & Cleaning the Dust Cup

Empty dust cup when full or after each use for optimal suction.

Turn off and unplug vacuum.
Press dust cup release button; remove cup from vacuum body.
Hold over trash can; press bottom release latch to open door and empty contents.
Close latch; reattach cup until it clicks.
Wipe cup with dry cloth if needed.

WARNING! Do not use water or liquids to clean dust cup. Ensure cup is completely dry before reattaching.

Filter Maintenance

HEPA filter should be cleaned monthly or when suction decreases.

Unplug vacuum.
Remove dust cup; locate filter compartment.
Take out HEPA filter; tap gently to remove loose dust.
Rinse filter under cold water until water runs clear. Do not use soap.
Air dry completely for 24 hours before reinstalling.

CAUTION! Never operate vacuum without filter or with wet filter.

Care & Storage

Unplug before cleaning or maintenance. Store in dry, cool place.

Clean brush roll regularly: Remove debris wrapped around roll. Check hose for clogs. Store with cord wrapped around hooks.

CAUTION! Do not store vacuum with wet filter or dust cup. Keep away from heat sources.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. For support, visit sharkclean.com or contact 1-800-798-7398. This product is covered by a limited warranty; see warranty card for details.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Loss of suction	Full dust cup, clogged filter or hose	Empty dust cup; clean filter; check hose for blockages.
Brush roll not spinning	Debris wrap, switch off	Clear debris from brush roll; ensure brush roll switch is ON.
Vacuum won't turn on	Power cord, outlet issue	Check power cord connection; try different outlet.
Lift-Away not detaching	Release button not fully pressed	Press release button firmly while lifting pod.
Unusual noise	Object stuck in hose or brush roll	Turn off, unplug, and inspect hose, nozzle, and brush roll for obstructions.

Reset: Unplug for 10 minutes; plug back in.

Service: 1-800-798-7398; sharkclean.com