Shark IQ ROBOT SELF-EMPTY XL Vacuum Cleaner Manual

The Shark IQ ROBOT SELF-EMPTY XL is an advanced robotic vacuum cleaner featuring intelligent mapping and navigation, self-emptying base station with XL capacity, Wi-Fi connectivity for app control and voice commands, multi-surface brushrolls, powerful suction, HEPA filtration, and smart sensor technology for obstacle avoidance. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation & Setup 3. First-Time Configuration 4. Specifications 5. Controls and Settings 6. Connecting to Wi-Fi & App 7. Cleaning Modes & Scheduling 8. Self-Emptying Base Station 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Robot vacuum, Self-Emptying Base Station, Charging Dock, Side Brushes, Multi-Surface Brushroll, Dust Bin, HEPA Filter, Power Adapter.

Feature	Description
IQ Navigation®	Intelligent mapping and room-by-room cleaning
Self-Empty Base	Automatically empties robot dust bin into base station
XL Capacity	Holds up to 30 days of dirt and debris
Wi-Fi Connectivity	Control via SharkClean® app and voice assistants
Multi-Surface Brushroll	Cleans carpets and hard floors without switching
HEPA Filtration	Traps 99.9% of dust and allergens
Smart Sensors	Detects and avoids obstacles, stairs, and drop-offs
Recharge & Resume	Automatically returns to dock to recharge and resumes cleaning
Voice Control	Works with Amazon Alexa and Google Assistant
Cleaning Modes	Eco, Normal, Max, and Spot Clean modes

Installation & Setup

Unpack and inspect all contents. Place base station on a level, open area.

Assemble base station: Connect power adapter to base and plug into wall outlet.
Prepare robot: Remove protective films from brushes and sensors.
Charge robot: Place robot on charging contacts at base station.
Clear cleaning area: Remove small objects, cords, and clutter from floor.

WARNING! Keep base station away from stairs and heat sources. Ensure charging area is dry.

First-Time Configuration

Power on robot; follow initial setup prompts.

Initial charge: Allow robot to charge fully (approx. 4 hours) before first use.
Download app: Install SharkClean® app from App Store or Google Play.
Connect to Wi-Fi: Follow in-app instructions to connect robot to your home network.
Create smart map: Let robot complete a full cleaning run to map your home.
Set preferences: Configure cleaning schedules, no-go zones, and room labels in app.

CAUTION! Do not move robot during initial mapping. Ensure Wi-Fi signal is strong in cleaning area.

Specifications

Model: Shark IQ ROBOT SELF-EMPTY XL
Navigation: IQ Navigation® with smart mapping
Dust Bin Capacity: 0.5 quarts (robot), 1.5 gallons (base station)
Run Time: Up to 90 minutes per charge
Charging Time: Approximately 4 hours
Suction Power: Adjustable (Eco, Normal, Max)
Filtration: Anti-Allergen Complete Seal with HEPA filter

Connectivity: 2.4 GHz Wi-Fi, Bluetooth

Voice Control: Amazon Alexa, Google Assistant

Power Source: 120V AC, 60Hz

Operating Temp: 32°F to 104°F (0°C to 40°C)

Controls and Settings

Access controls via physical buttons, SharkClean® app, or voice commands. Robot Buttons: CLEAN (start/pause), DOCK (return to base), SPOT CLEAN, Wi-Fi (connect).

App Controls: Start/stop cleaning, select rooms, set schedules, adjust suction, view cleaning history, set no-go zones, update software.

Cleaning Modes: Eco (quiet), Normal (balanced), Max (deep clean), Spot Clean (focused area). Smart Map: Edit rooms, label areas, set cleaning order. Base Station: Empty bin indicator, power button, filter access door.

Connecting to Wi-Fi & App

Requires 2.4 GHz Wi-Fi network and smartphone/tablet.

Ensure robot is powered on and near your Wi-Fi router.

Open SharkClean® app and create account or sign in.

Tap "+" to add device and select your robot model.

Follow on-screen instructions to connect to Wi-Fi (enter network password).

Once connected, name your robot and complete setup.

Tip: If connection fails, restart robot and router, ensure correct Wi-Fi band (2.4 GHz).

Cleaning Modes & Scheduling

Supports scheduled cleaning, room-specific cleaning, and manual control.

Start cleaning: Press CLEAN button on robot or use app/voice command.

Select mode: Choose Eco, Normal, or Max in app or during cleaning.

Spot clean: Press SPOT CLEAN button for intensive 2x2 ft area cleaning.

Schedule: In app, set daily/weekly cleaning schedules for specific rooms or whole house.

Room select: Choose specific rooms to clean via app after mapping complete.

Recharge & resume: Robot automatically returns to charge if battery low, then resumes cleaning.

Pause/resume: Press CLEAN button to pause; press again to resume.

Manual control: Use directional arrows in app for remote control mode.

WARNING! Clear floor of small objects, cords, and pet waste before cleaning. Do not use on wet surfaces.

Self-Emptying Base Station

Base station automatically empties robot's dust bin after cleaning cycles.

Operation: Robot returns to base after cleaning; base empties bin in 10-15 seconds.

Capacity: Holds up to 30 days of debris for average homes.

Indicator: LED lights show status (green=ready, red=full or error).

Empty base: When full indicator lights, lift bag access door, remove and replace dust bag.

Maintenance: Replace HEPA filter every 3-6 months; clean sensors monthly.

Note: Use only Shark-branded replacement bags and filters for optimal performance.

Care & Maintenance

Regular maintenance ensures optimal performance and longevity.

Daily: Empty robot bin if not using self-empty base; check for debris in brushes.

Weekly: Clean side brushes, multi-surface brushroll, and wheels; wipe sensors.

Monthly: Clean charging contacts on robot and base; check and clean filters.

As needed: Replace side brushes (every 6-12 months), brushroll (every 12-18 months), HEPA filter (every 3-6 months), dust bags.

CAUTION! Unplug base station before maintenance. Do not wash electronic components. Use dry cloth only.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. ICES-003: Complies with Canadian EMI regulations. Copyright © SharkNinja Operating LLC. All rights reserved. Shark, SharkClean, and IQ Navigation are trademarks of SharkNinja Operating LLC. For support, visit sharkclean.com or contact 1-888-228-5531.

Troubleshooting

Symptom Possible Cause Corrective Action

Robot won't start Low battery/not docked Ensure robot is properly docked and charging; wait for full charge.

Poor navigation Dirty sensors/obstacles Clean sensors with dry cloth; clear floor of obstacles and cords.

App connection lost Wi-Fi issues Restart robot and router; ensure 2.4 GHz network; reconnect in app.

Self-empty not working Full bag/clog Replace dust bag; check for clogs in base station hose.

Weak suction Full bin/clogged filter Empty dust bin; clean or replace filter; clear brushroll of debris.

Not returning to dock Blocked path/low battery Clear path to dock; ensure dock is powered and in open area.

Error sounds/lights Various issues Consult app for specific error code; refer to manual code list.

Reset: Hold DOCK and CLEAN buttons for 10 seconds to factory reset (erases maps).

Service: 1-888-228-5531; sharkclean.com/support

Shark IQ ROBOT SELF-EMPTY XL Vacuum Cleaner Manual © - All Rights Reserved 2025

Symptom	Possible Cause	Corrective Action
Robot won't start	Low battery/not docked	Ensure robot is properly docked and charging; wait for full charge.
Poor navigation	Dirty sensors/obstacles	Clean sensors with dry cloth; clear floor of obstacles and cords.
App connection lost	Wi-Fi issues	Restart robot and router; ensure 2.4 GHz network; reconnect in app.
Self-empty not working	Full bag/clog	Replace dust bag; check for clogs in base station hose.
Weak suction	Full bin/clogged filter	Empty dust bin; clean or replace filter; clear brushroll of debris.
Not returning to dock	Blocked path/low battery	Clear path to dock; ensure dock is powered and in open area.
Error sounds/lights	Various issues	Consult app for specific error code; refer to manual code list.