Shark HYDROVAC WD205 Vacuum Cleaner Manual

The Shark HYDROVAC WD205 is a powerful wet/dry vacuum cleaner designed for versatile cleaning tasks. It features a 5-gallon capacity tank, powerful suction for both wet spills and dry debris, a built-in blower function, a washable filter, a flexible hose with multiple attachments, and a convenient cord wrap. Powered by a standard 120V outlet. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: 5-Gallon Tank, Motor Unit, Hose Port, Blower Port, Power Switch, Cord Wrap, Washable Foam & Cloth Filter, Hose with Wand, Crevice Tool, and Wet/Dry Nozzle.

Setup & Assembly

Unpack all parts and inspect for damage. Assemble on a flat, stable surface.

1. Attach Wheels and Handle: Snap wheels into base slots; secure carrying handle to tank.
2. Install Filter: For dry pickup, place the foam sleeve over the filter cage, then cover with the cloth filter. Secure the filter cover.
3. Connect Hose: Insert hose end firmly into the hose port on the tank lid.
4. Attach Tools: Connect desired tool (wand, nozzle, crevice tool) to the other end of the hose.
5. Plug into Power: Ensure power switch is OFF. Plug cord into a standard 120V outlet.

WARNING! Do not use for wet pickup if the cloth filter is installed. Ensure all connections are tight before operation.

First-Time Use

Before first use, perform a quick function check.

1. Select Mode: Decide if you are picking up wet spills or dry debris.
2. Dry Pickup: Ensure foam and cloth filters are correctly installed.
3. Wet Pickup: Remove the cloth filter. Only the foam sleeve should be on the filter cage.
4. Power On: Press the power switch to ON. You should hear the motor engage.
5. Test Suction: Place hand over nozzle to feel suction.
6. Empty Tank: After testing, power OFF, unplug, and empty any collected material.

CAUTION! Never use without a filter for dry pickup. Never immerse motor unit in water.

Specifications

• Model: Shark HYDROVAC WD205.
• Tank Capacity: 5 Gallons (19 Liters).
• Motor: Powerful suction motor for wet/dry pickup.
• Functions: Vacuum (Wet/Dry) and Blower.
• Filtration: Washable Foam Sleeve and Cloth Filter.
• Hose Length: 5 ft. flexible hose.
• Attachments: Extension Wand, Crevice Tool, Wet/Dry Floor Nozzle.
• Power Source: 120V, 60Hz, AC.
• Cord Length: 10 ft. power cord with wrap.
• Weight: Approximately 12 lbs (empty).

Controls and Functions

Primary controls are located on the motor unit.

Power Switch: Rocker switch for ON/OFF operation.

Hose Port: For connecting the hose during vacuum mode.

Blower Port: For connecting the hose when using the blower function.

Filter Access: Twist-off lid for installing or removing filters.

Tank Lid Latch: Releases the lid for emptying the tank.

Tank Drain Plug: Remove to drain liquids from the tank.

Mode Selection: Function is determined by filter setup (wet/dry) and hose port connection (vacuum/blower).

Wet Pickup Mode

For cleaning up liquid spills, flooded areas, or wet debris.

1. Setup: Remove the cloth filter. Ensure only the foam sleeve is on the filter cage.
2. Ensure the tank is empty and the drain plug is securely closed.
3. Connect the hose to the VACUUM (Hose) port on the tank lid.
4. Attach the wet/dry floor nozzle or use the hose directly.
5. Plug in the vacuum and turn the power switch ON.
6. Clean the spill. Monitor the tank level to avoid overfilling.
7. When finished, turn power OFF and unplug.
8. Empty Tank: Carry the vacuum to a drain. Remove the drain plug to empty liquids. Rinse tank if necessary.

WARNING! Do not vacuum flammable liquids, hot ashes, or sharp objects. Do not leave liquids in the tank for extended periods.

Dry Pickup Mode

For cleaning dust, dirt, sand, and small dry debris.

1. Setup: Ensure both the foam sleeve AND the cloth filter are correctly installed on the filter cage.
2. Empty the tank of any previous contents.
3. Connect the hose to the VACUUM port.
4. Attach the desired tool (floor nozzle, crevice tool, wand).
5. Plug in and turn power ON.
6. Begin vacuuming. For fine dust, a slower pass may be more effective.
7. When finished or if suction drops, turn power OFF and unplug.
8. Empty Tank: Open the lid over a trash can to dispose of dry debris. Tap the filter to dislodge dust.

Tip: Regularly check and clean the filters during extended dry pickup sessions to maintain suction power.

Blower Function

Use to clear leaves, grass clippings, or debris from driveways, patios, and garages.

1. Setup: Ensure the tank is empty. No filter is required for blower function.
2. Disconnect the hose from the VACUUM port on the lid.
3. Connect the hose to the BLOWER port on the motor unit.
4. Attach the desired nozzle or use the open hose end.
5. Plug in the vacuum and turn the power switch ON.
6. Direct the airflow to move debris. Keep the hose end clear of obstructions.
7. When finished, turn power OFF and unplug. Disconnect the hose from the blower port.

CAUTION! Wear eye protection. Do not point hose at people, animals, or breakable objects. Use outdoors or in well-ventilated areas only.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

After Each Use: Empty the tank completely. Rinse the tank after wet pickup. Allow all parts to dry fully before storage.

Filter Cleaning (Dry Pickup):

1. Remove the filter cover and take out the cloth filter and foam sleeve.
2. Tap filters to remove loose dust.
3. Wash the foam sleeve in lukewarm water with mild detergent. Rinse thoroughly.
4. Hand-wash the cloth filter gently. Do not wring or twist.
5. Allow both filters to air dry COMPLETELY before reinstalling.

General Care: Wipe the exterior with a damp cloth. Check hose and attachments for clogs. Inspect the power cord for damage.

Storage: Store in a cool, dry place. Wrap the cord around the cord wraps. Store attachments in or near the tank.

WARNING! Never operate with wet filters. Always unplug before performing any maintenance.

Regulatory Information

This appliance complies with relevant safety standards. Copyright © SharkNinja Operating LLC. HYDROVAC is a trademark of SharkNinja. For support, replacement parts, or to locate a service center, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Note: For issues not listed, or if corrective actions do not resolve the problem, contact Shark Customer Service.

Service: 1-800-798-7398; www.sharkclean.com