Shark EP602 Vacuum Cleaner Manual

The Shark EP602 is a powerful upright vacuum cleaner designed for deep carpet cleaning and versatile floor care. It features a motorized brush roll, multiple suction settings, HEPA filtration, a large-capacity dust cup, LED headlights, and various attachments for above-floor cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Motorized brush roll, Suction control dial, HEPA filter, Dust cup with release button, LED headlights, Crevice tool, Upholstery tool, Dusting brush.

Assembly & Setup

Unpack and inspect all parts. Assemble before first use.

1. Attach handle: Insert handle into main body until it clicks into place.
2. Install wand: Insert wand into hose connector until secure.
3. Attach floor nozzle: Connect floor nozzle to wand until it locks.
4. Plug into wall outlet: Ensure power cord is fully unwound.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid injury.

First-Time Use

Plug in vacuum; turn on power button.

1. Select floor setting: Use suction control dial for carpets (high) or hard floors (low).
2. Engage brush roll: For carpets, ensure brush roll is ON; for hard floors, turn OFF.
3. Begin vacuuming: Push vacuum forward and back in overlapping strokes.
4. Use attachments: Detach wand and connect desired tool for above-floor cleaning.

CAUTION! Keep hair, cords, and loose clothing away from brush roll.

Specifications

• Model: Shark EP602 Upright Vacuum.
• Power: 120V, 60Hz, 12 Amps.
• Suction Control: Adjustable via dial (Low/Medium/High).
• Filtration: HEPA filter, washable pre-motor filter.
• Dust Cup Capacity: 1.5 liters.
• Cord Length: 25 feet.
• Attachments: Crevice tool, upholstery tool, dusting brush.
• Weight: 15 lbs.
• Warranty: 5-year limited warranty.

Controls and Settings

Main controls located on handle and body.

Handle: Power button, Suction control dial, Brush roll on/off switch.

Settings: Suction (Low for hard floors, Medium for low-pile carpets, High for deep cleaning). Brush roll (ON for carpets, OFF for hard floors to prevent scattering debris). LED lights (automatically illuminate in dark areas).

Using Attachments

For above-floor cleaning: detach wand and connect tools.

1. Turn off vacuum and unplug from outlet.
2. Press wand release button to detach from floor nozzle.
3. Connect desired attachment to end of wand or hose.
4. Plug in vacuum and turn on to use attachment.

Tip: Use crevice tool for corners; upholstery tool for fabrics; dusting brush for shelves.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Check brush roll monthly: Remove debris wrapped around brush roll.
2. Inspect hose and wand: Clear any blockages.
3. Wipe exterior: Use dry cloth to clean vacuum body.
4. Store properly: Wrap cord around hooks; store attachments in designated area.

WARNING! Always unplug vacuum before performing any maintenance.

Emptying the Dust Cup

Empty dust cup when full or after each use.

1. Turn off and unplug vacuum.
2. Press dust cup release button to remove cup.
3. Hold over trash can; press bottom release to open lid.
4. Tap gently to remove debris; close lid and reattach.

CAUTION! Do not overfill dust cup; empty regularly to maintain suction.

Filter Care

Clean filters every 3 months for best performance.

1. Unplug vacuum; remove HEPA filter from back compartment.
2. Tap filter over trash to remove loose dust.
3. Rinse under cold water; air dry completely for 24 hours before reinstalling.
4. Check pre-motor filter; rinse if dirty and air dry.

IMPORTANT! Never operate vacuum without filters installed.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © SharkNinja Operating LLC. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Reset: Unplug vacuum for 30 minutes if overheating occurs.

Service: 1-800-798-7398; www.sharkclean.com