Shark EP4535C Vacuum Cleaner Manual

The Shark EP4535C is a versatile upright vacuum cleaner featuring powerful suction, a HEPA filtration system, multiple cleaning modes (carpet, hard floor, above-floor), motorized brushroll, lift-away canister design, LED headlights, and a variety of attachments for comprehensive cleaning. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Upright vacuum body, lift-away canister, motorized brushroll, HEPA filter, dust cup, crevice tool, dusting brush, upholstery tool, wand, and power cord.

Assembly & Setup

Unpack and inspect all components. Assemble following steps.

1. Attach handle: Insert handle into upright body until it clicks securely.
2. Install wand: Insert wand into designated port on the vacuum body.
3. Attach hose: Connect hose to the lift-away canister and body.
4. Install filter: Place HEPA filter into the filter compartment.
5. Attach tools: Store attachments on onboard caddy.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching.

First-Time Use

Plug in vacuum; select appropriate cleaning mode.

1. Check filter: Ensure HEPA filter is properly installed.
2. Select mode: Use handle switch for Carpet, Hard Floor, or Above-Floors.
3. Adjust height: For carpets, set brushroll to appropriate pile height.
4. Begin cleaning: Press power button; move vacuum in slow, overlapping strokes.
5. Empty dust cup: When full, unplug and press release to empty.

CAUTION! Keep hair, loose clothing, and fingers away from brushroll.

Specifications

• Model: Shark EP4535C.
• Power: 120V, 60Hz, 10 Amps.
• Cord Length: 25 feet.
• Filtration: HEPA filter, washable foam filter.
• Dust Cup Capacity: 1.5 dry quarts.
• Cleaning Modes: Carpet, Hard Floor, Above-Floors.
• Attachments: Crevice tool, dusting brush, upholstery tool.
• Weight: 15.2 lbs.
• Warranty: 5-year limited warranty.

Controls and Settings

Handle controls: Power ON/OFF, Brushroll ON/OFF, Mode Selector (Carpet/Hard Floor/Above-Floors).

Indicator Lights: LED headlights (auto-on), filter check light (if clogged).

Brushroll Settings: Adjust for low/medium/high pile carpets. Suction Control: Automatic adjustment based on floor type. Lift-Away Release: Button to detach canister for portable cleaning.

Using Attachments

For above-floor cleaning: Detach canister and connect desired tool.

1. Detach canister: Press release button and lift away.
2. Select tool: Attach crevice tool, dusting brush, or upholstery tool to hose end.
3. Clean: Use tool on furniture, stairs, ceilings, or tight spaces.
4. Reattach: Return canister to upright body until it clicks.

Tip: Ensure vacuum is turned off when switching attachments.

Cleaning Modes

Three primary modes for different surfaces.

1. Carpet Mode: Brushroll spins for deep carpet cleaning.
2. Hard Floor Mode: Brushroll stops spinning to prevent scattering debris.
3. Above-Floors Mode: Use with lift-away canister and attachments.
4. Switch modes: Use selector on handle; LED indicates current mode.

WARNING! Do not use hard floor mode on carpets; may reduce cleaning effectiveness.

Maintenance & Care

Regular maintenance ensures optimal performance.

1. Empty dust cup: After each use; press release button.
2. Clean filters: Wash HEPA and foam filters every 3 months (air dry 24 hrs).
3. Clear brushroll: Remove hair and debris regularly; press release tabs.
4. Check hose: Remove clogs using long object.
5. Inspect cord: Check for damage; store with cord wrap.

CAUTION! Unplug before maintenance. Do not operate without filters.

Regulatory Information

UL Listed; complies with U.S. safety standards. Copyright © SharkNinja Operating LLC. For support, visit sharkclean.com or contact 1-800-798-7398. Keep these instructions for future reference.

Troubleshooting

Reset: Unplug for 10 minutes; plug back in.

Service: 1-800-798-7398; sharkclean.com