Shark CARPET GLIDER S3101 Vacuum Cleaner Manual

The Shark CARPET GLIDER S3101 is a lightweight, corded upright vacuum cleaner designed for deep carpet cleaning with a motorized brush roll, swivel steering, and a low-profile design for reaching under furniture. It features a 5-position height adjustment, a large-capacity dust cup, washable filters, a crevice tool, and an upholstery tool. Powered by 120V AC, 60Hz. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Setup 3. First-Time Use 4. Specifications 5. Controls and Settings 6. Using Attachments 7. Cleaning & Maintenance 8. Emptying the Dust Cup 9. Care & Storage 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Motorized brush roll, Swivel steering handle, 5-position height adjustment, Large-capacity dust cup, Washable foam and felt filters, Crevice tool, Upholstery tool.

Feature	Description
Motorized brush roll	Deep cleans carpets and agitates embedded dirt
Swivel steering	Provides easy maneuverability around furniture and obstacles
5-position height adjustment	Adjusts for different carpet heights and hard floors
Large-capacity dust cup	Holds more debris for fewer interruptions
Washable filters	Foam and felt filters can be rinsed and reused
Crevice tool	For tight spaces like corners and between cushions
Upholstery tool	For cleaning furniture, stairs, and car interiors
ON/OFF switch	Powers the vacuum cleaner on and off
Brush roll on/off	Disengages brush roll for hard floor cleaning
Low-profile design	Cleans under furniture with ease

Assembly & Setup

Unpack and inspect all contents. Assemble before first use.

Attach the handle: Insert the handle into the body until it clicks securely into place.
Install the dust cup: Ensure the dust cup is properly seated and locked.
Insert the filters: Place the foam filter over the felt filter and insert into the filter compartment.
Attach the hose and tools: Connect the hose to the port on the vacuum; store tools on caddy if provided.
Plug into AC power outlet.

WARNING! Ensure vacuum is unplugged during assembly. Handle with care to avoid pinching fingers.

First-Time Use

Before first use, perform a quick test to ensure proper operation.

Adjust height: Set the height adjustment to match your floor type (low for bare floors, higher for thick carpets).
Power on: Plug in, then press the ON/OFF switch to start the vacuum.
Test brush roll: Engage/disengage the brush roll to ensure it spins freely.
Check suction: Place hand over nozzle to confirm strong suction.
Empty dust cup: After initial test, empty the dust cup to ensure optimal performance.

CAUTION! Keep cord away from brush roll and moving parts. Do not vacuum wet surfaces.

Specifications

Model: CARPET GLIDER S3101.
Type: Corded upright vacuum cleaner.
Power Source: 120V AC, 60Hz.
Cord Length: 25 feet.
Dust Cup Capacity: 1.2 dry quarts.
Filters: Washable foam and felt filters.
Attachments: Crevice tool, upholstery tool.
Height Adjustment: 5 positions.
Brush Roll: Motorized, with on/off control.
Weight: Approximately 12 lbs.

Controls and Settings

Main controls located on the handle and body.

Handle: ON/OFF switch, Brush roll on/off button (if applicable).

Body: Height adjustment lever (usually at the base), Dust cup release button, Hose release button.

Settings: Height adjustment (Position 1 for low-pile carpets to Position 5 for thick carpets; Position 0 or bare floor setting for hard surfaces). Brush roll on for carpets, off for hard floors or delicate rugs.

Using Attachments

For above-floor cleaning, use the hose and tools.

Turn off and unplug the vacuum.
Detach the hose from the storage port.
Connect desired tool (crevice or upholstery tool) to the end of the hose.
Plug in and turn on the vacuum to use the attachment.
After use, turn off, unplug, and store tools properly.

Tip: For best suction with attachments, ensure the dust cup is not full and filters are clean.

Cleaning & Maintenance

Regular maintenance ensures optimal performance and longevity.

Empty dust cup: Empty after each use or when full.
Clean filters: Rinse foam and felt filters monthly under lukewarm water; let air dry completely for 24 hours before reinstalling.
Check brush roll: Regularly remove hair and debris wrapped around the brush roll. Use scissors to cut and remove if necessary.
Inspect hose and tools: Clear any clogs from the hose or attachment nozzles.
Check cord: Inspect power cord for damage before each use.

WARNING! Always unplug the vacuum before performing any maintenance. Do not operate with wet filters.

Emptying the Dust Cup

To maintain suction, empty the dust cup regularly.

Turn off and unplug the vacuum.
Press the dust cup release button and lift the cup out of the vacuum body.
Hold over a trash can and press the bottom release latch to open the door, allowing debris to fall out.
Close the door securely and reinsert the dust cup until it clicks into place.

CAUTION! Empty dust cup outdoors or in a well-ventilated area if allergic to dust.

Care & Storage

Unplug and cool down before storing. Store in a dry place.

Wrap cord around cord hooks (if provided). Hang or stand upright to avoid damage to the brush roll. Keep away from heat sources and moisture.

CAUTION! Do not store with a full dust cup. Ensure filters are completely dry before storage.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B. This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © SharkNinja Operating LLC. Shark and CARPET GLIDER are trademarks of SharkNinja Operating LLC. For support, visit www.sharkclean.com or contact 1-800-798-7398.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Vacuum won't turn on	Power source/switch	Check if plugged in; ensure outlet works; press ON/OFF firmly.
Loss of suction	Full dust cup/clogged filters	Empty dust cup; clean or replace filters; check hose for clogs.
Brush roll not spinning	Obstruction/engagement	Turn off, unplug, and remove debris from brush roll; ensure brush roll is set to ON.
Vacuum is difficult to push	Height setting	Adjust height to a higher setting for thick carpets.
Unusual noise or smell	Obstruction/overheating	Turn off and unplug immediately; check for blockages in hose, brush roll, or intake; let motor cool if overheated.

Reset: Unplug for 60 minutes to reset thermal protector if motor overheats.

Service: 1-800-798-7398; www.sharkclean.com