Shark AI360ROBOT Vacuum Cleaner Manual

The Shark AI360ROBOT is an advanced robotic vacuum cleaner featuring AI-powered navigation, 360-degree obstacle detection, self-emptying base station, multi-surface cleaning with auto-adjust suction, Wi-Fi connectivity for app control, voice command compatibility, scheduled cleaning, zone targeting, and recharge & resume functionality. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Unpacking and Setup 3. First-Time Configuration 4. Technical Specifications 5. Controls and Indicators 6. Connecting to Wi-Fi and App 7. Cleaning Modes and Scheduling 8. Maintenance and Care 9. Regulatory and Safety Information 10. Troubleshooting

Features at a Glance

Key components: Robot vacuum, Self-Empty Base Station, Charging Dock, Side Brushes, High-Efficiency Filter, Remote Control, Power Adapter.

FeatureDescription
AI NavigationUses sensors and cameras to map rooms and avoid obstacles
Self-Empty BaseAutomatically empties robot's dustbin into sealed bag
Multi-Surface CleaningAuto-adjusts suction for carpets and hard floors
Wi-Fi & App ControlControl via SharkClean app (iOS/Android)
Voice ControlWorks with Amazon Alexa and Google Assistant
Recharge & ResumeReturns to dock to recharge, then resumes cleaning
Zone CleaningTarget specific areas via app
Boundary StripsVirtual no-go zones (set in app)
HEPA FiltrationCaptures 99.9% of dust and allergens
Quiet ModeReduced noise for nighttime cleaning

Unpacking and Setup

Unpack and inspect all contents. Place base station on a level surface against a wall.

  1. Install side brushes: Snap onto bottom of robot.
  2. Charge robot: Place on charging dock; ensure power is connected to base station.
  3. Install dust bag: Open base station lid, insert bag until it clicks.
  4. Clear area: Remove small objects, cords, and loose rugs from floor.

WARNING! Keep away from stairs and wet areas. Ensure charging contacts are clean and dry.

First-Time Configuration

Power on robot; follow initial setup prompts.

  1. Initial charge: Allow robot to charge fully (approx. 4 hours).
  2. Download app: Install SharkClean app from App Store or Google Play.
  3. Connect to Wi-Fi: Follow in-app instructions to connect robot to 2.4GHz network.
  4. Name your robot: Assign a unique name in app for voice control.
  5. First cleaning run: Press CLEAN on robot or app to start initial mapping.

CAUTION! Do not move base station during initial mapping. Ensure Wi-Fi signal is strong.

Technical Specifications

Controls and Indicators

Robot Top: POWER, CLEAN, SPOT CLEAN, DOCK. Base Station: POWER indicator, Empty Bin button, Wi-Fi LED.

App Controls: Start/Pause, Schedule, Zone Cleaning, Suction Settings, History, Error Alerts.

Indicator Lights: Blue (charging/ready), Flashing Blue (cleaning/error), Red (low battery/error). Voice: Use "Alexa, ask Shark to start cleaning" or "Hey Google, tell Shark to dock."

Connecting to Wi-Fi and App

Ensure robot is on dock and powered.

  1. Open SharkClean app, create account or log in.
  2. Tap "+" to add device, select "Robot Vacuum".
  3. Follow prompts to connect to 2.4GHz network (5GHz not supported).
  4. Enter Wi-Fi password when prompted.
  5. Wait for connection confirmation (Wi-Fi LED solid blue).

Tip: If connection fails, restart robot and router, ensure robot is within range.

Cleaning Modes and Scheduling

Supports Auto, Quiet, Max, and Spot cleaning modes.

  1. Start cleaning: Press CLEAN on robot or app, or use voice command.
  2. Select mode: In app, choose Auto (default), Quiet (low noise), Max (deep clean).
  3. Spot Clean: Press SPOT button for concentrated 2x2 ft area cleaning.
  4. Schedule: In app, set daily/weekly cleaning times.
  5. Zone Cleaning: Draw zones on map in app for targeted cleaning.
  6. Recharge & Resume: Enabled by default; robot returns to dock if battery low, then resumes.
  7. Pause/Stop: Press CLEAN button or use app to pause; DOCK to return.

WARNING! Do not pick up robot during cleaning; allow it to complete cycle or dock first.

Maintenance and Care

Regular maintenance ensures optimal performance.

TaskFrequencyInstructions
Empty Robot DustbinAfter each cleaningPress release button, empty into trash.
Clean Side BrushesWeeklyRemove, wipe clean of hair/debris.
Clean Main BrushMonthlyRemove, cut away wrapped hair/debris.
Clean Sensors & CameraMonthlyWipe with dry microfiber cloth.
Replace FilterEvery 3-6 monthsRemove old filter, insert new HEPA filter.
Replace Base Station BagWhen full (app alert)Open lid, remove full bag, insert new one.
Clean Charging ContactsMonthlyWipe robot and dock contacts with dry cloth.

CAUTION! Unplug base station before maintenance. Do not wash filters; tap to clean.

Regulatory and Safety Information

FCC Compliance: This device complies with Part 15 of FCC rules. Operation subject to conditions: (1) not cause harmful interference, (2) accept any interference received. ICES-003: Class B digital apparatus. Copyright © SharkNinja Operating LLC. For support, visit sharkclean.com/support or contact 1-888-228-5531.

Troubleshooting

SymptomPossible CauseCorrective Action
Robot not startingLow battery/not dockedPlace on dock to charge; ensure power connected.
App connection failedWi-Fi issuesEnsure 2.4GHz network; restart robot and router; check password.
Robot stuck/errorObstacles/sensor blockedClear path; wipe sensors; move to new location, press CLEAN.
Poor suctionFull dustbin/blockageEmpty dustbin; check for clogs in brush and air path.
Not returning to dockObstructed path/dock movedClear path to dock; ensure dock is in open area, plugged in.
Base not emptyingFull bag/clogReplace bag; check hose for blockage.
Voice command not workingApp not linkedLink Shark skill in Alexa/Google Home app; ensure robot online.

Reset: Hold DOCK and SPOT buttons for 10 seconds to reset Wi-Fi settings.

Service: 1-888-228-5531; sharkclean.com/support

Shark AI360ROBOT Vacuum Cleaner Manual © - All Rights Reserved 2025